Wrench Size Needed to Tighten Anti Rattle Bolt for Swagman XTC4 4-Bike Rack

Question

Question:

What size of wrenc/socket can be used to tighten /loosen this up?

asked by: Igmedio S

0

Expert Reply:

The Swagman XTC4 4-Bike Rack # S64665 referenced in your question does include an anti-rattle hitch lock. In order to tighten or loosen the bolt you can use a 19mm wrench or socket wrench. I have attached a short video demonstration on this bike rack that you can also check out.

expert reply by: Chris R

0

Answer 1

I went to our warehouse and measured the Leveling Scissor Jack #JSC-24-IND. The bolts on the #JSC-24-IND are 2 inches apart center to center, just like they are in your photo. When closed, the stand measures 4 inches from the base to the top of the…

view full answer...

Answer 2

Yes, you can install a Curt Trailer Hitch Receiver #C11433 on your 2019 Chevrolet Spark. This receiver is capable of supporting up to 200lbs of tongue weight. With each of the Lectric 3.0 e-bikes weighing roughly 60lbs without the battery you will…

view full answer...

Answer 3

We noticed when we installed the etrailer Trailer Hitch Receiver #e98856 on a similar 2022 Jeep Wrangler it had 8" from the center of the hitch pin to the rear edge of the stock spare tire. This would likely not allow you to fold up the…

view full answer...

Answer 4

The Hollywood Racks RV Rider #HLY64FR has a frame clamp design that was intended for use with step through style bike frame like what your Aventon Adventure bikes have so this rack would work perfect for you. I attached a picture that shows this…

view full answer...

Answer 5

The Hollwood Racks #HLY64FR is an excellent choice for most users with an RV towed Jeep Wrangler. If your jeep has a standard size spare on the back, like the one in the picture I have attached, then you can see that you will have plenty of room with…

view full answer...

Answer 6

Only certain bike racks are rated for use at the back of an RV or trailer but the Hollywood Racks #HR1400Z bike rack is not one of them. Generally, any rack that can fold or tilt, with few exceptions, won't be rated for this applications. The…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Your best platform bike rack for spare clearance is the RV Rider part #HLY64FR as it has the most clearance between the hitch pin hole and the wheel trays. This has 12 inches from the pin hole to the pivoting portion of the rack but then has even…

view full answer...

Answer 9

We have exactly what you need in the Hollywood Racks RV Rider Bike Rack for 2 Electric Bikes, #HLY64FR. This bike rack was designed to carry two bikes on an RV. The RV Rider has an 80 lb. per bike weight capacity so it can be used with e-bikes, has a…

view full answer...

Answer 10

A smaller hitch extender like the Curt part #C45791 would work to give you the additional clearance for your Hollywood Racks RV Rider part #HLY64FR that you need.

view full answer...

Answer 11

There's no difference at all. The #HLY64FR is our unique part number for the Hollywood Racks HR1700 RV Rider bike rack, it's the same exact bike rack just by a different part number. The RV rider is a great choice for carrying heavy electric…

view full answer...

Answer 12

In order to use a hitch-mounted bike rack like the Swagman Original #S64152-2 that you were looking at while towing a vehicle, you will just need to add the Roadmaster Dual Hitch Receiver Adapter #RM-077-4. This adapter will slide into the 2 inch…

view full answer...

Wrench Size Needed to Tighten Anti Rattle Bolt for Swagman XTC4 4-Bike Rack

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching