Diameter of Holes on Mounting Brackets of Hitch Bracket # 4916

Question

Question:

What is the diameter of the holes for this part?

asked by: Grant

0

Expert Reply:

I checked with Draw Tite and the size bolt recommended for the mounting holes of the brackets # 4916 is 5/8 inch which is the diameter of the holes.

expert reply by: Jameson C

0

Answer 1

The Weld-on Bracket Kit #4916 is meant to be welded on meaning the crosstube gets welded to the brackets and the brackets to the frame. The brackets went through a design change and may or may not have holes in them. Either way they are meant to be…

view full answer...

Answer 2

Thanks for the picture, and the measurements! I took a look at your bumper, and it doesn't appear that the Mount-n-Lock GennyGo Generator and Cargo Carrier for RV Bumpers #MNT54FR will be a good fit for you. This cargo carrier will fit square and…

view full answer...

Answer 3

The mounting plates included with the Curt Class V Universal Weld-On Receiver #15903 you were looking at are slightly different that the 16" Weld-On Bracket Kit #4916 you mentioned. Our warehouse measured the #15903 brackets and they measure…

view full answer...

Answer 4

I do not ahve the abilty to pull an OEM build sheet for part numbers however, we have a couple options available. The Single Slide-Out Switch, #37212285 is a 12V 40-amp continuous/momentary switch assembly. With cutout dimensions of 1.85" tall x…

view full answer...

Answer 5

The best option we have available for your 2008 Sterling Bullet Cab and Chassis is the Draw-Tite Ultra Frame Service Body Trailer Hitch #41991 paired with the 16" Weld-On Bracket Kit #4916. These extra long brackets will give you the drop needed…

view full answer...

Answer 6

The Curt Adjustable Trailer Hitch Receiver, Class III - 2", #C13701 that you link to, has a maximum gross trailer weight rating of 5,000 lbs. However, this is increased to a maximum GTW of 6,000 lbs. when used with weight distribution system. My…

view full answer...

Answer 7

We do carry universal hitches that are rated for 10,000 pounds and above, like the Draw-Tite part #41990-07. I've linked the selection. With that being said a lot of times when a motorhome is rated for 5,000 pounds towing it isn't the hitch…

view full answer...

Answer 8

I was unable to find the capacity of your existing trailer hitch to determine if it can pull the 5,300 pound trailer. The only way I can guarantee a hitch will be able to pull that much weight would be to replace the hitch. Draw-Tite hitch #41990 is…

view full answer...

Answer 9

The main difference between the Dometic 310 Part-Timer RV Toilet #DOM57FR and the Dometic 311 Part-Timer RV Toilet #DOM67FR is that the 310 is standard height (20" tall) and the 311 is a low profile (15-1/2" tall). Both toilets will mount…

view full answer...

Answer 10

We may have something that will work for you, but keep in mind, trailer hitch manufacturers do not make custom fit hitches for RVs and motor homes. A universal hitch is used and is typically bolted or welded to the frame of the RV and in some cases…

view full answer...

Answer 11

The Dometic 311 Part-Timer RV Toilet #DOM67FR does not come with the hand sprayer but you can add it with the Installation Kit #DOM75FR. I confirmed this with my contact at Dometic.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Diameter of Holes on Mounting Brackets of Hitch Bracket # 4916

Product Page this Question was Asked From

Continue Researching