10k Gooseneck Trailer Jack Recommendation with Handle and Non-Spring Return

Question

Question:

do you have any 10k gneck jacks no spring loaded any brand with handles

asked by: C&M T

0

Expert Reply:

I have a great solution for you. The Bulldog Jack part # BD182411 is a 10k jack that can be attached to your gooseneck trailer and does not have a spring return. To add a handle you'd then want the part # BD015181.

expert reply by: Jameson C

0

Answer 1

We do not carry that replacement part from the manufacturer. The closet we have is the Replacement Thread Forming Screw 1/2" #58437. These are larger than what the manufacturer uses so it may require alteration.

view full answer...

Answer 2

I recommend installing the Air Lift LoadLifter 5000 Ultimate Air Springs #AL88338 for your 2016 GMC Sierra 3500 Denali. These air springs include internal jounce bumpers which help to absorb bounce when loaded and will also absorb road shock in the…

view full answer...

Answer 3

Generally this is an issue with the remote #AL73002 communicating with the system #AL74000, a blockage, or a leak. I would inspect the compressor system and all of the air lines to make sure there are no issues. You can check for leaks using soap and…

view full answer...

Answer 4

When these types of jacks fail, they often just need to be replaced. You may be able to find a part if you were able to dismantle it and figure out the issue, but that part may not even be available as a replacement. Since your existing jack…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 10

Yes, the Air Lift LoadLifter 5000 Air Helper Springs #AL57341 will fit your 2024 Chevrolet Silverado 2500 double cab with the Duramax diesel engine and factory puck system. We installed the upgraded Springs #AL88341 on a similar 2022 which I have…

view full answer...

Answer 11

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 12

Yes, the Air Lift LoadLifter 5000 Ultimate Air Helper Springs #AL88341 will fit with the B&W Turnoverball Underbed Gooseneck Trailer Hitch #BWGNRK1020 on your 2024 Chevrolet Silverado 2500. I prefer these air springs as they have the internal…

view full answer...

10k Gooseneck Trailer Jack Recommendation with Handle and Non-Spring Return

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching