Where Do I Position My New Trailer Axle?
Question:
I put straight axles back exactly where old torsion axle was. My question is, Will this change anything on my trailer being the torsion axle tires where recessed back further than the straight axle?
asked by: Dwaine
Expert Reply:
When positioning a trailer axle or adding an additional axle, the key is to make sure that the axles are located in just the right position so that roughly 10 to 15 percent of the total trailer weight is placed on the tongue. Finding the correct axle location can take some trial and error, so it is best to mock up the locations for all the suspension components until you know everything is in the right spot.
I have a diagram and a help article attached that will show you how to recalculate your tongue weight.
Putting your straight axles in the exact same place as the old torsion axles were may work, it will just depend on how your tongue weight calculates. If you find that your trailer's tongue weight is less than 10 to 15 percent of the total trailer weight, then the trailer axle will need to be moved further away from the trailer tongue, closer to the back of the trailer. If you find that your trailer's tongue weight is greater than 10 to 15 percent of the total trailer weight, then the trailer axle will need to be moved closer to the trailer tongue and the front of the trailer.
Product Page this Question was Asked From
Dexter Trailer Axle Beam with EZ-Lube Spindles - 89" Long - 3,500 lbs
- Trailer Axles
- Leaf Spring Suspension
- Easy Lube Spindles
- No Hubs
- 3500 lbs
- Spindles Only
- 74 Inch Long
- 89 Inch Long
- No Drop or Lift
- Dexter
more information >
Continue Researching
- Shop: Dexter Trailer Springs Over-Under Conversion Kit
- Shop: Front/Center/Rear Hanger for Double-Eye Springs - 4-1/4" Tall - 9/16" Bolt Hole
- Search Results: rear hanger
- Shop: Single-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front, 1-1/4" Rear
- Shop: Rear Hanger with Bushing for Single Axle Trailer Suspensions with 1-3/4" Double Eye Springs
- Search Results: spring hanger
- Shop: Front/Center/Rear Hanger for Double-Eye Springs - 3-1/4" Tall - 9/16" Bolt Hole
- Search Results: axle flip kit
- Search Results: trailer jack
- Search Results: trailer fenders
- Search Results: leaf spring hangers
- Search Results: 29~31
- Article: Double-Eye Trailer Suspension System Review
- Article: Slipper Spring Trailer Suspension System Review
- Shop: Ram Round A-Frame Trailer Jack - Topwind - 14-7/8" Travel - Zinc - 3,000 lbs
- Shop: Front/Center/Rear Hanger for Double-Eye Springs - 3-5/8" Tall - 9/16" Bolt Hole
- Q&A: Where to Start When Trying to Determine Axle Placement on a Boat Trailer
- Video: Review of Trailer Valet Removable Wheel For JXS Trailer Jacks - TV89FR
- Article: How to Raise Your Travel Trailer Height
- Article: Where to Position the Trailer Axle?
- Q&A: How to Determine the Correct Axle Position When Building a Trailer
- Q&A: Recommendation To Make A 1-1/2 Inch Diameter Jack Compatible With A Caster Wheel For 2 Inch Jacks
- Q&A: Recommended Bolt On A-Frame Trailer Jack For Karavan 6' X 12' Utility Trailer
- Video: Review of etrailer Straight Tongue Trailer Coupler - Standard Coupler - CT-3001-Z
- Video: Review of Titan Brake Actuator - T4820000
- Q&A: Single Axle Trailer, Should the Hanger or Shackle Be on the Front of the Trailer Frame
- Q&A: Hanger Spacing Needed for Single Axle Trailer with 25-1/4 inch Long Leaf Springs
- Q&A: Would Dexter 3,500 lb Axle Made in 1999 Use Same Hubs as Current
- Article: Trailer Wiring Diagrams
- Article: Trailer Tire Sizing