Pipe Mount Jack Recommendation for Trailer that Has Wheel Caster Option
Question:
Hi, I am interested in the following articles and I have still questions: - Replacement Mounting Bracket for Trailer Valet Swivel Jack and Trailer Mover Item # TV-0002 - Bulldog 2-4/5inch Long, Weld-On Jack Pipe Mount for 3-1/4inch Male Mount and 7/8inch Pin Item # BD005122 - Replacement Pipe for etrailer and Ram Pipe Mount Swivel Jacks - 2-1/2inch - 5/8inch Pin Hole Item # TJP-OP58 - Square Pipe Mount Swivel Jack w Footplate - Leg - Weld On - Sidewind - 15inch Travel - 7K Item # TJDP-7000S-B - I want a tire for the Square Pipe Mount Swivel Jack, is this part right? Replacement 6" Caster Wheel for Bulldog Trailer Jack with 2" Tube Diameter - Qty 1 # BD500245 I would like that Replacement mounting bracket for trailer on mytrailer mount. Is it possible the other parts with the Replacement mounting bracket for trailerinch to connect and to use the patch? I would like to install the Jack Pipe only when needed. If the parts dont match, is it possible that you are calling the appropriate article Jack and Tire? Im looking forward to a message. Best regards
asked by: Ronald S
Expert Reply:
For the square jack part # TJDP-7000S-B that you referenced we do not have a wheel that will replace the foot. The reason is that the wheels have lower capacities around 1,200 lbs and this jack has a 7k capacity.
If you wanted a similar option with a wheel you'd want the # BD1541150301 for a jack with the wheel caster # BD500245 that you referenced. For the pipe mount you'd then want the part # BD015279.
Products Referenced in This Question
Replacement 6" Caster Wheel for Bulldog Trailer Jack with 2" Tube Diameter - Qty 1
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Jack Wheel
- 6 Inch Wheel
- Wheel w Caster Assembly
- Bulldog
more information >
Square Pipe Mount Swivel Jack w Footplate - Drop Leg - Weld On - Sidewind - 28-1/2" Lift - 7K
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 6001 - 7000 lbs
- Sidewind Jack
- Swivel Jack
- 28 Inch Lift
- Pipe Mount
- Weld-On
- With Rectangle Foot
- etrailer
more information >
Product Page this Question was Asked From
Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 10" Lift - 2,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Sidewind Jack
- Swivel Jack
- 10 Inch Lift
- Pipe Mount
- Weld-On
- No Wheel or Foot
- Bulldog
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Pintle-Hitches
- Q&A: Does The etrailer Invisible Base Plate Kit # e86YR Need An Adapter For A Blue Ox Aventa II Tow Bar
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Q&A: Recommended Replacement AC Unit For A Coleman Mach On A 2000 Mesa Pop Up Camper
- Q&A: B&W 4 Inch Offset Gooseneck Ball for a 2015 GMC Sierra 2500 Short Bed
- Article: Brake Controller Installation: Starting from Scratch
- Article: How to Install a Brake Controller on Chevrolet / GMC 1999-2006 Pickups
- Q&A: Recommended Tuner for 2018 Ford F-150 with 5.0L Engine
- Q&A: How to Determine if Dexter Tandem-Axle Trailer Hanger Kit for 2-1/2 Slipper Springs Will Work
- Q&A: Is a Wheel Available for a Pipe-Mount Swivel Trailer Jack
- Q&A: Can The Foot Plate On The Round, Pipe Mount Swivel Jack # TJP-5002S-B Be Changed To a Wheel?
- Article: Gooseneck Trailer Hitch Information and Review
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Wiring Trailer Lights with a 6-Way Plug (It's Easier Than You Think)