Does Trailer Hitch from 1999 Ford E-150 also Fit 2001 Ford E-150

Question

Question:

Hello will a tow hutch from 2001 Ford E150 fit on a 1999 Ford E150

asked by: Brandi

0

Expert Reply:

Yes, a hitch from a 1999 Ford E-150 would also fit a 2001. For example, the Draw Tite part # 41906 fits both years and would be a great option. You might still verify the part number of the hitch if you can find it.

expert reply by: Jameson C

0

Answer 1

The distance between the mounting holes from side to side on the Draw Tite trailer hitch part #41945 are 38-1/2 inches. This hitch fits the following vehicles: 2004 - 2014 Ford Van E-150 2004 - 2014 Ford Van E-250 2004 - 2014 Ford Van E-350 2000 -…

view full answer...

Answer 2

It sure won't. The cast receivers used by the Draw-Tite UltraFrame Hitches like the #41945 are extremely tough and have been fully tested to ensure they meet the 10K GTW/1500 lb tongue weight capacities. As long as the weight capacities…

view full answer...

Answer 3

For your 1997 Fleetwood Pace Arrow 35U Ford E-350 Cutaway Chassis the correct front hitch is the Draw Tite part #65001 that you referenced. This has been tested as a fit for your van and would work without requiring you to measure anything to…

view full answer...

Answer 4

The Curt #14055 will actually sit just about flush with the edge of the bumper once installed on your 2006 Ford E-350. Though this will meet the weight capacities you need, if you are looking for something to completely clear the bumper, it will fall…

view full answer...

Answer 5

The Draw-Tite Ultra Frame Trailer Hitch Receiver w/ Cast Center #41946 is a confirmed fit for the 1996-2018 Chevy Express and GMC Savana Vans. There is not a confirmed fit for any E450 models, but I did measure the hitch as you requested to see if…

view full answer...

Answer 6

Yes, the Draw-Tite Ultra Frame Trailer Hitch Receiver part #41945 is a fit for a 2001 Ford Van with step bumper. I have attached a photo below of the hitch installed on a model with a step bumper.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Does Trailer Hitch from 1999 Ford E-150 also Fit 2001 Ford E-150

Products Referenced in This Question

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching