Can the Hopkins Wiring Kit # HM56200 and T-One # 118416 be Installed on a 2017 Jeep Wrangler
Question:
Your FAQ seem to say yes and no depending upon which question/answer I view. I would like to flat tow and have trailer wiring on the jeep.
asked by: Scott
Expert Reply:
You can indeed use the Hopkins Custom Tail Light Wiring Kit # HM56200 for flat towing your 2017 Jeep Wrangler even if you already have the T-One # 118416 already installed. If you check out the 1:45 mark on the attached video of the Hopkins kit being installed you can see this process being done.
I couldn't quite find any specific places where we recommended against using these products together but I think you were referencing when we recommended using the Flexo-Coil Wiring Kit # RM-15267 instead of the Hopkins kit. I personally prefer the Flexo-Coil kit over the Hopkins because most RVs tend to have a 6-Way or 7-Way connector at their rear bumper and some vehicles require the battery to be disconnected.
This kit has a 7-Way connector for the RV side so no adapter is needed and in the case of the battery needing to be disconnected you can simply install a Charge Line Kit # RM-156-25 to the middle pin on the 6-Way connector to keep your battery charged.
I looked up your owner's manual and it looks like you turn the key in your Jeep to "Off" so a charge line kit may not be necessary. Either wiring kit would be a great option for your application.
Please note that a complete flat towing setup includes a base plate kit, tow bar, safety cables, vehicle tow bar wiring, a supplemental braking system, and usually a high-low adapter. If you are needing any of these please let me know and I can make some recommendations.
Be sure to check out your copy of the owner's manual for any specific instructions on flat towing.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Tow Bar Wiring
- Splices into Vehicle Wiring
- Diode Kit
- Universal
- Tail Light Mount
- Roadmaster
more information >
Roadmaster Battery Charge Line Kit for Towed Vehicles
- Accessories and Parts
- Tow Bar Wiring
- Battery Charge Line Kit
- Roadmaster
more information >
Product Page this Question was Asked From
Hopkins Custom Tail Light Wiring Kit for Towed Vehicles
- Tow Bar Wiring
- Plugs into Vehicle Wiring
- Wiring Harness
- Custom
- Tail Light Mount
- Hopkins
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Recommended Flat Towing Setup for a 2016 Jeep Wrangler Using a ReadyBrute Elite II Tow Bar
- Article: Flat Towing Package for 2007-2018 JK Jeep Wrangler and Wrangler Unlimited
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams
- Q&A: Recommended Flat Towing Components For A 2024 Chevy Trax
- Article: Must-Have Flat Towing Components
- Article: Roadmaster Vehicle Specific Base Plates
- Article: Wiring Trailer Lights with a 6-Way Plug (It's Easier Than You Think)
- Q&A: Which Bumpers Can I Flat Tow a Jeep Wrangler JLU With Using D-Ring Adapters
- Article: Tow Bar Wiring: Which Wiring Kit is for You?
- Q&A: What do I Need to Flat Tow a Jeep Wrangler JK with Factory Bumper
- Q&A: Is The Curt C96JR Tail Light Kit Compatible With A Brake Buddy Brake System?
- Q&A: Will The Curt Dinghy Wire Harness # C96JR Interfere With Activation Of A Blue Ox Patriot
- Q&A: Choosing Between the Brake Buddy Select 3 and the Blue Ox Patriot Supplemental Braking System