Parts Needed to Add a 7-Way Trailer Connector on a 2011 Ford E-250 Without a Tow Package
Question:
I have a 2011 Ford E-250 van that I need a trailer wiring harness for. It does not have a tow package. Do you have a t connector wiring harness that has the 4 pin flat connector and the 7? I can’t find it.
asked by: Phil G
Expert Reply:
There is a T-One connector to fit your 2011 Ford E-250 for a 4-way. Use part # 118551. However, to add a 7-way you need to connect some wiring. Once you have the 4-way installed use our # ETBC7 kit to convert it to the 7-way and still keep your 4-way. The # ETBC7 plugs into your existing 4-way and also has the additional wires that are then run to your battery for 12 volt power, your van's reverse lights, and then to the cab to connect to an electric brake controller. Once installed you'll have both a fully functioning 7-way and 4-way. The kit includes everything but the controller itself. I've linked a video of the install process for you.
If you also need a brake controller I recommend the P3, part # 90195, because of how easy to use and reliable it is. Also if you don't have a hitch yet you can use part # 75703 with our ball mount kit, part # 989900.
Products Referenced in This Question
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class IV
- 600 lbs TW
- 6000 lbs GTW
- 10000 lbs WD GTW
- 2 Inch Hitch
- 1000 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- Tekonsha
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Product Page this Question was Asked From
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Choose the Right Trailer Hitch Class
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Determining Trailer Tongue Weight
- Article: Rooftop Cargo Carriers
- Article: What Do I Need To Tow A Trailer?
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Q&A: Recommended Trailer Wiring Harness for 2012 Ford Escape
- Q&A: Differences between the Curt Trailer Hitch # C13651 and # 13650 for a Ford Escape
- Q&A: What is the Difference Between a Class II Trailer Hitch and Class III Trailer Hitch
- Q&A: Adding a 7-Way Trailer Wiring Harness to a 2008 Ford E-150 Van with Factory 4-Way
- Q&A: 7-Way Recommendation for a 2009 Ford E-350 Van
- Q&A: Trailer Hitch Confirmed To Fit 2009 Ford Edge