Replacement Frame Brackets for Fastway e2 Weight Distribution Systems
Question:
Will these work with the old style L brackets? Or do I have to buy the whole L brackets kit.
asked by: Michael
Expert Reply:
The l-brackets on the Fastway e2 Weight Distribution Systems have not changed. As long as there are 6 bolt holes on the bracket then the Replacement Outer Link Plate part # FA93-02-5350 will work well for you. If you have an l-bracket with 8 bolt holes then this is an Equal-i-zer part and the Fastway outer link bracket will still work but not with the 4th and 5th bolt holes.
If you end up needing to replace the entire frame bracket assembly you can do so using the following:
Fastway:
(2) Replacement Outer Link Plate part # FA93-02-5350
(2) Replacement Sway-Control L-Bracket part # FA93-02-5150
(2) Replacement Inner Link Plate part # FA93-02-5200
(1) Replacement Hardware Kit part # FA92-02-9200
Equal-i-zer:
(2) Replacement Sway-Control Bracket part # EQ95-01-5600
Products Referenced in This Question
Replacement Sway-Control Bracket for Equal-i-zer Weight Distribution - 6,000 lbs to 14,000 lbs GTW
- Accessories and Parts
- Weight Distribution Hitch
- Frame Bracket
- Equal-i-zer
- Equal-i-zer
more information >
Replacement Hardware Kit for Fastway Sway Control Brackets
- Accessories and Parts
- Weight Distribution Hitch
- Sway Control Parts
- Brackets
- e2
- Fastway
more information >
Replacement Sway-Control L-Bracket for Fastway e2 Weight Distribution Systems - 6,000 to 12,000 lbs
- Accessories and Parts
- Weight Distribution Hitch
- Hardware
- Brackets
- e2
- L-Bracket
- Fastway
more information >
Replacement Inner Link Plate for Fastway e2 Sway-Control Bracket
- Accessories and Parts
- Weight Distribution Hitch
- Sway Control Parts
- Link Plate
- e2
- Fastway
more information >
Product Page this Question was Asked From
Replacement Outer Link Plate for Fastway e2 Sway-Control Bracket
- Accessories and Parts
- Weight Distribution Hitch
- Sway Control Parts
- Link Plate
- e2
- Fastway
more information >
Continue Researching
- Shop: Trailer Hub and Drum Assembly - 7,000-lb Axles - 12" Diameter - 8 on 6-1/2 - Pre-Greased
- Shop: Dexter Electric Trailer Brakes - 12" - Left/Right Hand Assemblies - 7,000 lbs
- Shop: Water Heater Door Latch
- Shop: Adjustable Width Trailer Hitch Receiver for RVs, 22" to 66" Wide
- Shop: Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide
- Shop: Fifth Wheel Hitch
- Shop: Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 5,500 lbs
- Shop: Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 6,500 lbs
- Q&A: Split View or Single Camera View for Furrion Vision S Wireless RV Backup Camera System
- Shop: RV Exterior Lighting
- Q&A: Torque Figure for Tightening Fastway E2 Link Plates
- Q&A: How Tight Should Frame Bracket Plates Be When Installing Fastway E2 Weight Distribution System
- Q&A: What Stays on the Trailer and What Stay on the Truck with the Fastway e2 Weight Distribution System
- Q&A: Recommendation For Weight Distribution Shank With Maximum Height Of 12-1/2 Inches
- Q&A: Recommended Weight Distribution Shank for 4 Inch Drop with Fastway e2 10,000 lb System
- Q&A: Height of Equal-i-Zer Shank # EQ90-02-4200