What is the Size of the Opening for the Safety Chain Quick Link # C82932

Question

Question:

What is the dimension for the opening on your product Item # c82932? I am having a heck of a time finding a way to hook up my safety chains via their clevis hooks on my smaller trailers. Mating them to my stock 2016 Chev Silverado 2500 HD receiver hitch which has a very strange safety chain hook up arrangement.

asked by: Roy B

0

Expert Reply:

The Safety Chain Quick Link # C82932 that you referenced has an opening of about 5/8". (0.625 of an inch.)

If you check out the attached review video at about the 0:54 mark you can see this measurement being taken.

expert reply by: Jon G

0

Answer 1

The only quick link that we have which may work for your application is the Curt 16.5K #C82932. The opening is 5/8" so I'm not sure how much of a difference that extra 1/8" will make. Aside from that everything else we have…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey John, we actually have a supplemental braking system that was designed specifically to be used with the Spartan K2 chassis you have that has the Safe Haul system with the Demco Air Force One Flat Tow Brake System part #DM54YV so this would be the…

view full answer...

Answer 5

If you want to just add on some sort of extension you can use Safety Chain Quick Link #C82932 which has a working load limit of 3300-lbs. This will give you about 3-inches additional length. Ideally trailer safety chains will be one continuous chain,…

view full answer...

Answer 6

Yes, the Gen-Y Torsion weight distribtuion shank part #325-GH-1102 that you reference will work great with your Pro Series weight distribution as it was designed to have same bolt pattern.

view full answer...

Answer 7

In this situation, most folks either replace the safety chains, using a hook that will fit. Another option would be to use a quick link, like #C82932. Attach the quick link to the safety chain hole in the hitch, then attach the safety chain hook to…

view full answer...

Answer 8

I called and emailed JR Products multiple times with no response so instead of purchasing the Quick Links - 1/2" #37201345 I recommend going with the Curt Threaded Quick Link - 1/2" Diameter #C82932, which have a safe working weight load of…

view full answer...

Answer 9

Using a Reducer Sleeve #e28JR is not going to reduce your trucks towing capacity unless you are using a lower capacity hitch. As you are most likely using a weight distribution hitch you should not have any issue with towing your 10,000LB travel…

view full answer...

Answer 10

I checked with Valterra and the StayPut Stand Pads like #A10-0924 can hold up to 40,000 lbs gross vehicle weight on a firm level ground, or 10,000 lbs per wheel.

view full answer...

Answer 11

As you have the Monitor #TST-507-D-C you will simply need the Signal Booster #TST-507-R to go along with some new tire sensors. You do have the option of what sensors you will prefer to use from the list below. Brass Tire Sensors for TST TPMS - Qty 2…

view full answer...

What is the Size of the Opening for the Safety Chain Quick Link # C82932

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching