Extra-Long Ball Mount for Use with 2014 Range Rover HSE 2-Inch Hitch
Question:
Hi, I need a ball receiver with 2inch , 2inch ball and pin. I also need the shank to be at least 8inch long as the receiver on the Range Rover is set back a bit. Can you point me to the right set up? thanks
asked by: Brian D
Expert Reply:
It sounds like you are looking for an extra-long ball mount for a 2-inch hitch that will give you more room between your Range Rover Rover HSE and your trailer.
Brophy ball mount # BM20 measures 13-1/4-inches from the center of the hitch pin hole to the center of the ball hole. This ball mount provides either 3/4-inch rise or 2-inches of drop, depending on how you install it in your hitch.
Draw-Tite ball mount # 2753 measures 9-inches from the hitch pin hole to the ball hole. This ball mount provides either 2-3/4-inches of rise or 4-inches of drop.
For a 2-inch hitch ball to use with these ball mounts you can use part # 40038. For a basic pin/clip use # PC3 or for a lock use # e98880.
Products Referenced in This Question
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 4 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Draw-Tite
more information >
Brophy Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 13-1/4" Long - 10K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 0 Inch
- Fits 2 Inch Hitch
- 10000 lbs GTW
- Class IV
- Brophy
more information >
etrailer Trailer Hitch Receiver Lock for 2" Hitches - Flush - 2-5/8" Span - Chrome
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Alike
- Chrome
- Fits 2 Inch Hitch
- Flush Pin
- 2-5/8 Inch Span
- etrailer
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
2" Hitch Ball - 1" Diameter x 2-1/4" Long Shank - Chrome - 12,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/4 Inch Shank Length
- 1 Inch Diameter Shank
- 12000 lbs GTW
- Class III
- CURT
more information >
Continue Researching
- Q&A: Torque Recommendation for Tightening Curt Hitch Ball to Ball Mount
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Recommended Weight Distribution Hitch For A Jayco Jay Flight SLX 174BHW
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Q&A: Tongue Weight Capacity of 2018 Chevy Equinox With Curt Trailer Hitch
- Q&A: Replacement Tail Light For Bargman 6-1/2 Inch Oval Light
- Article: Enjoy The 2024 Eclipse With Harvest Hosts
- Q&A: Can Sway Control Be Used on a Trailer that Uses a Pintle Hitch Set Up
- Q&A: Do Amber Lights of Hollywood Racks Bike Rack Taillight Kit HLY54RR Light up With Brake Lights
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Parts Needed to Add Brake Controller to 2024 Toyota Sienna Platinum
- Article: Steel vs. Aluminum Ball Mounts
- Article: 2 Steps for Finding the Right Weight Distribution Hitch Size
- Article: Best Bike Racks for Electric Bikes