Prodigy P3 Reading No Trailer Connected With 2002 Chevy Silverado
Question:
I have a 2002 Chevrolet Silverado, pre-wired tow package. I purchased the Tekonsha 90195 P3 controller, and 3025 -P harness. It powers, but says no trailer connected and will not work the electric trailer brakes. Checked wiring, and the wires going into my 7 way connector are all hooked up and run in a factory harness to the front of truck. I believe either the brake controller is faulty or the 3025-P is wrong . Any help?
asked by: Paul
Expert Reply:
Oftentimes when the reading says your trailer is not connected when using the Prodigy P3 # 90195, the cause is a connector that has corrosion or dirt built up, and ensuring they are clean inside and out can be a remedy. There are tests you can do as well.
You will need to find out if the issue is on the brake controller, truck, or trailer. To test the brake controller, sever the blue wire a couple inches from the back of your controller. Then use a circuit tester such as # PTW2992 to test the end of the blue wire coming out of the controller. It should only have power when you apply the manual override; if it shows power at idle then there is an issue with the controller, and it will need to be replaced.
You will also want to test the brake output pin on the 7-way socket; it should only show power with the manual override. If it shows power any other time, then there is a short somewhere between the connector and the brake controller you will need to find.
If the truck side checks out, then it could be the wiring to the brake magnets or possibly the magnets themselves. Inspect the power wires to the magnets and look for wires that may be pinched or otherwise damaged and fix as necessary. You'll also need to make sure the ground wires are attached to bare metal surfaces, free of any paint, dirt or corrosion.
You'll want to visually inspect the magnets; if you can see the copper windings coming through the magnets will need to be replaced. To test the magnets, you can follow the help article I have linked. I have also attached some help articles on testing and troubleshooting brake controllers for you to check out.
Products Referenced in This Question
Product Page this Question was Asked From
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Brake Controller Installation: Starting from Scratch
- Article: Trailer Wiring Diagrams
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Installing an Electric Brake Controller on 2007-2013 GM Full-Size Truck or 2007-Present GM SUV
- Article: How to Install a Brake Controller on Chevrolet / GMC 1999-2006 Pickups
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Q&A: Does the Tekonsha P3 Trailer Brake Controller Turn Off or Stay On All the Time
- Q&A: Parts Needed To Install A Brake Controller On A 2023 Freightliner Cascadia
- Q&A: Suspension Enhancement Recommendation for 2019 Toyota RAV4
- Q&A: How Does Brake Controller Install on Freightliner S2RV Chassis
- Q&A: Parts Needed to Add 7-Way & Brake Controller on 2023 Kia Sportage
- Q&A: Wiring Configuration for Tekonsha Prodigy P3 Trailer Brake Controller 90195