Needing New Trailer Hub for a 1962 Aloha 16 foot Trailer
Question:
Needing new hub My inter bearing is LM 48548 and the bearing race is lm 48510 My outer bearing is stamp m12649 I have a 5 on 41/2 wheel spacing on 15 in wheel My axel is from a 1962 aloha trailer 16 ft Axel is 1 n a half in thick Thank u for any information
asked by: David
Expert Reply:
I do have a way that you can put replacement hubs on your 1962 Aloha Trailer, but unfortunately we do not have any hubs that use those bearings.
If you are restoring or updating this trailer then it may be easier to just replace your axle so that you can easily find replacement parts.
You can try matching the leaf spring and spring center measurements of our standard axles so they match with your trailer, but I recommend using a Timbren Rubber Spring Suspension instead. The Timbren Axle-Less suspension is much easier to install than the traditional axle plus it can increase the ground clearance of your trailer. You could use part # A35RS545 which include the hub assemblies that have a 5 on 4-1/2 inch bolt pattern, and use the common Inner Bearing # L68149, Outer Bearing # L44649, and Grease Seal # RG06-050.
I have attached an installation video for you to reference should you choose to go this route.
Products Referenced in This Question
Replacement Trailer Hub Bearing - L44649
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.063 Inch I.D.
- Bearing L44649
- Race L44610
- 3500 lbs Axle
- etrailer
more information >
Replacement Trailer Hub Bearing - L68149
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.378 Inch I.D.
- Bearing L68149
- Race L68111
- 3500 lbs Axle
- etrailer
more information >
Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.719 Inch I.D.
- 2.565 Inch O.D.
- etrailer
more information >
Product Page this Question was Asked From
Timbren Axle-Less Trailer Suspension w Idler Hubs - Standard Duty - No Drop - 5 on 4-1/2 - 3,500 lbs
- Trailer Axles
- Rubber Spring Suspension
- Easy Lube Spindles
- Idler Hubs
- 3500 lbs
- 5 on 4-1/2 Inch
- Universal Fit
- No Drop or Lift
- Timbren
more information >
Continue Researching
- Shop: Timbren Axle-Less Trailer Suspension w Idler Hubs - Standard Duty - No Drop - 5 on 4-1/2 - 3,500 lbs
- Article: Trailer Tire Sizing
- Q&A: Idler Hubs, Bearings, Seals and Grease For a 2015 V22L ShoreLand'r Boat Trailer
- Q&A: Does Bearing Buddy Seal Kit # BB60002 Fit 3,500 lb Trailer Axle
- Article: Trailer Wiring Diagrams
- Article: Most Popular Wheel Bearings
- Q&A: Axle Upgrade for my Harbor Freight 1720 Utility Trailer
- Q&A: Can 3,500 Lb Hub be Used to Replace 2,000 Lb Hub with Same Size Bearings
- Q&A: Recommended Parts for Rebuild/Upgrade of Harbor Freight Trailer
- Q&A: Proper Spacing Between the Hub Face and Spring Center Locations for 7,000-lb Triple Axles
- Q&A: Replacement Axle-Less Trailer Suspension Square Axle 49.5 Hub Face and 38.5 Spring Center
- Article: 2023 Holiday Must Haves
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Brake Controller Installation: Starting from Scratch
- Article: Determining Trailer Tongue Weight