Measuring Trailer Spindle for Correct Replacement Bearings
Question:
I have an 1994 ez loader boat trailer need to replace the bearing, the measurement of A=1.7inch B=1.5inch C=1.4inch D=1.1 the race outer diameter is 2.6. Which replacement kits should I order? Thanks!
asked by: Tony W
Expert Reply:
When measuring your trailer spindle at various locations to determine the correct bearing replacements, I recommend using a digital caliper like # PTW80157. This is because the measurements will need to be as exact as possible and extended out to the third decimal point.
For example, there are a few inner bearings that are close to the 1.4 inch measurement you provided for "C" on the spindle. The bearing # LM48548 has an inner diameter of 1.375 inches, # L68149 has an inner diameter of 1.378 inches and # 29749 has an inner diameter of 1.5 inches.
You can also check to see if the bearing numbers are stamped into the bearings themselves on your existing set. Determining the axle capacity on your trailer will also help to narrow down the possibilities. I have attached a couple of articles on trailer bearings that you might also find helpful.
Products Referenced in This Question
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.500 Inch I.D.
- Bearing 29749
- Race 29710
- 3000 lbs Axle
- etrailer
more information >
Replacement Trailer Hub Bearing - L68149
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.378 Inch I.D.
- Bearing L68149
- Race L68111
- 3500 lbs Axle
- etrailer
more information >
Replacement Trailer Hub Bearing - LM48548
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.375 Inch I.D.
- Bearing LM48548
- Race LM48510
- 2500 lbs Axle
- TruRyde
more information >
Product Page this Question was Asked From
4" Carbon Fiber Digital Caliper
- Hand Tools
- Measuring and Layout Tools
- Digital Calipers
- Carbon Fiber
- Performance Tool
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: Replacement Bearings and Seals for a ShoreLandr Trailer with Dico 45263 Hubs
- Shop: Bearing Kit, L44649 Inner/Outer Bearings, 10-9 Seal
- Shop: Bearing
- Shop: Replacement Trailer Hub Bearing - L44649
- Shop: Double Lip Seal for 3,700-lb Marine Hubs
- Search Results: l44649
- Shop: Trailer Hitch
- Q&A: How to Tell if Trailer has a BT8 or BTR Spindle Installed
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Article: Most Popular Wheel Bearings
- Q&A: Timken Replacement Bearing Solution for Setup with Part Numbers L44649 471750 L44610
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Search Results: 25580
- Shop: Grease Seals 10-36 (pair)
- Shop: Trailer Wiring
- Article: Trailer Wiring Diagrams
- Video: Bearing Buddy Trailer Bearings Races Seals Caps - Seals - BB60011 Review
- Search Results: bearing buddy
- Shop: Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2
- Shop: Brake Controller
- Q&A: What is Difference Between Trailer Bearings L44649 vs L44643
- Shop: Gooseneck Hitch
- Article: Trailer Tire Sizing
- Video: TruRyde Bearing Kit for #84 Spindle Installation
- Search Results: l68149
- Q&A: Are Bearings L44549 and L44649 Interchangeable
- Search Results: bearing kit
- Video: etrailer Trailer Idler Hub Assembly Review and Installation
- Shop: Suspension Enhancement
- Article: How to Tell the Weight Rating of a Trailer Axle