Trailer Hitch and Wiring Recommendation for 2006 Honda Odyssey
Question:
Good evening, I am interested in purchasing a tow hitch for a 2006 Honda Odyssey and would like to know which hitch would be the least restrictive i terms of ground clearance for steep inclines? I plan to initially use the hitch for intent for a bike rack but may eventually get a trailer. The trailers I have seen utilize a 4 wire system. Are the 4 wire plugs compatible with ettrailer wiring kits? Thank you.
asked by: Ryan S
Expert Reply:
On a low sitting vehicle like your 2006 Honda Odyssey trailer hitches are going to reduce ground clearance since they have to hang below the rear bumper. The Draw Tite part # 75270 is a confirmed fit, tucks right up under the rear bumper and would be great for towing or bike rack.
For trailer wiring you then would want the part # 118438 which is a confirmed fit and is the 4-way style of harness like you mentioned.
If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag.
If the ball mount kit does not include a ball mount with the right rise or drop to tow the trailer level, check out the link I have included that explains how to measure to choose a ball mount to tow the trailer level.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 675 lbs TW
- 4500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 675 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Choose the Right Trailer Hitch Class
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: My Trailer Hitch Doesn't Fit
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Recommended Hitch for VelociRAX 5 Bike Rack on 2012 Honda Odyssey
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Q&A: Comparison Between Draw-Tite 76025 and EcoHitch 306-X7253 for 2015 Honda Odyssey
- Article: How to Measure for Trailer Hitch Drop
- Article: Trailer Wiring Diagrams
- Article: Transmission Cooler
- Q&A: Choosing OEM or Aftermarket 5th Wheel Puck System for 2021 Ford F-250
- Q&A: How To Install a 7-Way Trailer Connector On a 2016 Honda Odyssey
- Q&A: Honda Odyssey Custom Built Class III Round Tube Trailer Hitch Bolt Sizes
- Q&A: Solution for Keeping RV Furrion Refrigerator Doors Closed when Travelling