How to Pick Out Landing Gear for Kaufman Car Trailer
Question:
i need an electric landing gear for my trailer . kaufman 3 car trailer. do you have anything that can work?
asked by: Shane
Expert Reply:
In order to pick out a direct replacement for the landing gear on your trailer we would need to know the distance between the mounting brackets. Otherwise you could just have the brackets removed from your trailer by a qualified welder and then install the brackets that come with the Reese Bulldog Tandem Landing Gear Set # RP500708. Either way this landing gear set would work well for you, you just might have to have the brackets of your trailer removed and reinstalled or replaced.
I attached a picture that shows the dimensions that this landing gear set would fit with.
The jacks would be the correct replacement for Lippert, Venture, and Atwood landing gear, as well as those from a few other manufacturers. The sure way to tell is that if the distance between the mounting brackets (underside of top bracket to top of lower bracket as shown in the diagram) is 17-1/2 inches. If this is the case, the landing gear should fit just fine.
If your frame clamps are instead 20-1/4 inches the Ultra Fab part # UF17-943010 would be a direct replacement.
Products Referenced in This Question
Ultra-Fab Deluxe Electric Landing Gear Set - 38" Lift - 12,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 10001 lbs or More
- Electric Jack
- Landing Gear
- 38 Inch Lift
- Weld-On
- 2 Jacks
- Ultra-Fab Products
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Replacement Shackle Strap for E-Z Flex Heavy Duty Rubber Suspension System by Dexter
- Shop: Replacement Flange Nut for Dexter Trailer Suspension Kits
- Shop: Replacement Shackle Link with Bolts for Dexter Trailer Suspension Kits
- Q&A: Does Chrome Edge Trim # SAT012ET Have an Adhesive Backing
- Shop: Chrome Edge Trim - 50' Roll
- Search Results: trailer fender trim
- Q&A: Lug Nut Torque Setting for 14-Inch Steel Trailer Wheels on 1/2-Inch Wheel Studs
- Q&A: Does Jack Height Matter When Picking Out A-Frame Trailer Jack
- Q&A: Can You Use 2 Sets of TrailerLegs Tire Saver Stands on Triple Axle Trailer if You Stay Within Weight
- Shop: Replacement Magnet Kit for 10" Electric Trailer Brake Assemblies - 3,500 lbs
- Search Results: trailer jack parts
- Q&A: Torque Specs for 3500-lb 5-on-4-1/2 Dexter Hub/Drum 84546UC3
- Shop: Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2
- Q&A: Does HBA-CAM Adapter Module for Hydrastar Electric Over Hydraulic Brake Actuators have 2 or 4 Wires
- Shop: Trailer Hitch
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: 44649
- Video: Choosing the Right Trailer Wiring
- Shop: Grease Seals 10-36 (pair)
- Shop: Trailer Wiring
- Article: Trailer Wiring Diagrams
- Q&A: Recommended 16' Mesh Tarp for Dump Trailer
- Search Results: 68149
- Video: etrailer Class III Trailer Hitch Installation - 2016 Jeep Cherokee
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Shop: Brake Controller
- Search Results: 25580
- Shop: Fifth Wheel Hitch
- Search Results: dust cap
- Article: Trailer Tire Sizing