Is Bumper Modification Required to Install a Trailer Hitch on a 2011 Mercedes GLK 350
Question:
Do you have to cut or change the bumper to fit the hitch? Do you have to reprogram anything for the electrical? Thanks
asked by: David
Expert Reply:
The rear bumper on your 2011 Mercedes GLK 350 should not have to be modified in order to install Draw-Tite Trailer Hitch, # 75698. However, you may need to bend or remove some tabs on the rear fascia to install the hitch properly. This is covered in the installation instructions I have linked for you to view.
For trailer wiring on higher end European vehicles such as your GLK, I recommend using the Mercedes part and having the dealer install it to avoid any potential problems they may come up with an aftermarket part.
If you plan on doing some towing, the recommended ball mount is # AMSC2 and you can use pin and clip # PC3. For a ball, you can use # 19260 (1-7/8 inch diameter), # 19247 (2 inch diameter), or # 63847 (2-5/16 inch diameter).
Products Referenced in This Question
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
2-5/16" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2-5/16 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Draw-Tite
more information >
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Matte Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 10000 lbs GTW
- Class IV
- Shock Absorbing
- Convert-A-Ball
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 600 lbs TW
- 4000 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Recommended Floor Mats for Motorhome Built on Ford E-450 Chassis
- Q&A: Easier to Install Trailer Hitch Recommendation for 2012 Mercedes GLK350
- Article: Wiring Trailer Lights with a 6-Way Plug (It's Easier Than You Think)
- Q&A: How To Determine Blue Ox Spring Bar Weight Capacity
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: My Trailer Hitch Doesn't Fit
- Q&A: etrailer Hitch Design for 2013 Mercedes-Benz GLK350
- Article: Trailer Hitch Installation Tips
- Article: How to Choose the Right Trailer Hitch Class
- Article: Frequently Asked Questions About Transmission Coolers
- Article: How to Raise Your Travel Trailer Height
- Article: How Much Does a Boat and Trailer Weigh?