Trailer Hitch and Wiring for a 2002 Chevy Blazer
Question:
What are the Bolt hole to bolt hole measurements on this hitch for a 2002 Chevy blazer?
asked by: Tanner
Expert Reply:
I went out to the warehouse to measure Draw-Tite trailer hitch # 75079 for you. The inside width from mounting flange to mounting flange is approximately 40-15/16 inches. Outside it is 41-9/16 inches. Since this is a custom fit part provided you have a vehicle this hitch was designed for fit will not be a problem. Your 2002 Chevy Blazer is one of the vehicles this hitch fits.
If you plan on doing some towing I recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag.
If the ball mount kit does not have the right rise or drop to tow the trailer level, use the link I have included that explains how to measure to choose a ball mount to tow the trailer level.
And you can use wiring harness # C58044 to add a 4-Way flat connector to the rear of the vehicle. I included a link to a generic install video that shows the process of identifying vehicle wires for installation.
![Michael H](https://images.etrailer.com/static/images/catg/people/324_tn.jpg)
Products Referenced in This Question
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Curt 4-Way Flat Trailer Connector w/ 60" Harness and Wire Taps
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- 5 Feet Long
- Universal Fit
- 4 Flat
- CURT
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 600 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Front Mount Hitch
- Shop: Trailer Wiring
- Article: Trailer Hitch Receiver Sizes
- Q&A: Replacement RV Microwave for Apollo Microwave AAC24OTRB
- Q&A: Does Draw Tite Hitch # 75079 Fit 2001 Chevy Blazer 2 Door
- Q&A: Wiring Diagram for Hydrastar Vented Marine Electric Over Hydraulic Actuator Installation
- Q&A: How to Tell If Your Breakaway Switch Is Powered By Trailer Battery or Auxiliary Battery
- Q&A: Replacement Trailer Wheel for Dexstar Wheel 17-293
- Q&A: Replacement Motor/Operator Parts for a Ventline Ventadome V2119
- Q&A: Replacement Power Center For a Magnetek Model 80
- Article: How to Bleed Your Trailer Surge Brakes
- Article: Trailer Wiring Diagrams
- Article: What To Look For When Buying Ratchet Straps
- Article: My Trailer Hitch Doesn't Fit
- Article: 5 Things to Know About Weight Distribution Hitches
- Article: Which Hitches are Made in the USA