6 inch Drop Ball Mount Recommendation for Truck Towing Motorcycle Trailer
Question:
My truck sits up high. The motorcycle trailer tongue is 13inch off ground. The bottom of my truck receiver where it goes in is 17inch off ground. The top of the square hole on receiver is 19. So do I need a 4inch ? What do you recommend?
asked by: Jackie
Helpful Expert Reply:
When determining how much drop you need from a ball mount you have to measure from the top of the hitch opening to the ground and then from the bottom of the coupler lip on the trailer down to the ground when it is sitting level.
So since you measured from the bottom of the 2 inch hitch and got 17 inches that would mean you need a drop of 6 inches actually.
For a ball mount you then would want the part # 40346 which has a 6 inch drop.
For a hitch ball with a 2 inch diameter you then would need the part # 63845 or for a 2-5/16 inch part # 63840.
Products Referenced in This Question
Draw-Tite Ball Mount - 4-3/4" Rise, 6" Drop - 10-1/4" Long - 6,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 6 Inch
- Rise - 5 Inch
- Fits 2 Inch Hitch
- 6000 lbs GTW
- Class III
- Draw-Tite
more information >
2-5/16" Hitch Ball - 1-1/4" Diameter x 2-3/4" Long Shank - Chrome - 20,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2-5/16 Inch Diameter Ball
- 2-3/4 Inch Shank Length
- 1-1/4 Inch Diameter Shank
- 20000 lbs GTW
- Class IV
- Class V
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Product Page this Question was Asked From
Draw-Tite Ball Mount - 4-3/4" Rise, 6" Drop - 10-1/4" Long - 6,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 6 Inch
- Rise - 5 Inch
- Fits 2 Inch Hitch
- 6000 lbs GTW
- Class III
- Draw-Tite
more information >
Continue Researching
- Shop: Curt Ball Mount for 2" Hitches - 8" Rise, 9-1/4" Drop - 14" Long - 5K
- Search Results: 6" rise
- Search Results: 4" rise
- Shop: Curt Ball Mount - 6" Rise, 8" Drop - 11-1/2" Long - 5,000 lbs
- Shop: Curt Class I Drawbar - 4" Rise - 9" Long - 2,000 lbs
- Shop: Draw-Tite Ball Mount - 4-3/4" Rise, 6" Drop - 10-1/4" Long - 6,000 lbs
- Shop: Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
- Shop: Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
- Video: Choosing the Right Trailer Wiring
- Shop: Trailer Hitch
- Search Results: hitch
- Article: How to Measure for Trailer Hitch Drop
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: Trailer Wiring
- Video: Choosing the Right Brake Controller
- Search Results: trailer hitch
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: trailer brake controller
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Trailer Wiring Diagrams
- Shop: Suspension Enhancement
- Shop: Brake Controller
- Q&A: Does Truck with 6-1/2 ft bed Have to Use Slider Hitch for Turning Clearance with Fifth Wheel Hitch
- Article: The 5 Best Trailer Drop Hitches You Can Buy
- Search Results: trailer jack
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 90160
- Video: Timbren Axle-Less Trailer Suspension System Installation