Can Stromberg-Carlson Replacement RV Ladder Support Peg # 8531-B be Trimmed Down to 7 Inches

Question

Question:

I need a tube length of approx 7 inches. Can this 12 inch tube be trimmed to fit my application?

asked by: Rick H

0

Expert Reply:

You could trim down the Replacement Ladder Support Peg # 8531-B to 7 inches. You would want to remove the cap at the end and cut it to length from that end (the end that attaches to the ladder). Then you could put the cap back on.

expert reply by: Michael H

0

Answer 1

If you cut the replacement ladder support part #8531-B down to 5-1/2 inches you do not need a new expansion nut. You can remove the plastic cap from the peg, push the star shaped nut down (pictured in the photo) and cut the peg. Then replace the…

view full answer...

Answer 2

Yes, you could trim down the Replacement Ladder Support Peg #8531-B to 5 inches. You would want to remove the cap at the end and cut it to length from that end (the end that attaches to the ladder). Then you could put the cap back on.

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 10

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 11

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 12

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Can Stromberg-Carlson Replacement RV Ladder Support Peg # 8531-B be Trimmed Down to 7 Inches

Product Page this Question was Asked From

Continue Researching