Can LED Trailer Light Kit part # TLL9RK be Backed Into Water on Boat Ramp

Question

Question:

I have a 2013 GMC 1/2 ton towing a 12foot EZ-Loader trailer. It has the square standard lights. Will the submersible LED work probably? I think the truck puts out 14+ volts.

asked by: Carl O

0

Expert Reply:

The submersible LED trailer light kit part # TLL9RK is designed to be backed into water like when installed on a boat trailer. We still recommend unplugging the trailer wiring just because water and electricity don't like to mix well. We are aware that a lot of people leave them plugged in without any issue.

expert reply by: Jameson C

0

Answer 1

This Submersible LED Trailer Light Kit with 25 foot Wiring Harness, part #TLL9RK, uses all stainless steel mounting hardware. The mounting hardware of this trailer light kit should work well in the saltwater conditions that you use your boat in.

view full answer...

Answer 2

I went out to the warehouse and pulled the Waterproof, Under 80 inch LED Trailer Light Kit, item #TLL9RK, to see exactly what Optronics means by waterproof. Upon initial inspection the housing itself is not water tight. Water can access the housing…

view full answer...

Answer 3

I included an image below with the measurements for the openings for the Trimax Outboard Motor Lock #TMX32ZR. The large slot is 4-1/2" wide while the narrow slot is 2" wide. The portion between the openings is 2-1/4" wide…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on…

view full answer...

Answer 9

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on…

view full answer...

Can LED Trailer Light Kit part # TLL9RK be Backed Into Water on Boat Ramp

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching