Timbren Suspension Enhancement Recommendation for 2011 GMC Yukon XL Denali

Question

Question:

Does the system for a 2011 Yukon XL fit the Denali?? Theyre both the same frame

asked by: Efrain

1

Helpful Expert Reply:

For your 2011 GMC Yukon XL the correct Timbren kit for the rear axle is the part # TGMRYS4. This fits the Denali models as well so it would be the correct fit for you.

expert reply by: Jameson C

1

Answer 1

Yes, the Timbren kit part #TGMRYS4 that you referenced does fit the 4 wheel drive models of the 2013 GMC Yukon with auto leveling suspension.

view full answer...

Answer 2

The maximum gross trailer weight (GTW) and tongue weight (TW) capacity of your 2004 GMC Yukon will vary from 5,700 lbs to 12,000 lbs depending on chassis (1500,2500,3500), drive (2WD,4WD), gear ratio (3.42,3.73,4.10), and GCWR (Gross Combined Weight…

view full answer...

Answer 3

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 8

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Timbren Suspension Enhancement Recommendation for 2011 GMC Yukon XL Denali

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching