Trailer Hitch & Wiring for 2017 Nissan Juke
Question:
2017 Nissan Juke not listed for trailer hitches. Are the 2016 same as the 2017. I need a Curt hitch and trailer light wire kit with powered converter.
asked by: Henry
Helpful Expert Reply:
We do show confirmed hitch fits for the 2017 Nissan Juke, for non-NISMO models. You can see all products on the linked page. We do have Curt options but I suggest the lower-price Draw-Tite.
If you have the AWD model you can use Draw-Tite Class I hitch # 24867; if you have the FWD model you can use the Draw-Tite # 24892. For both you can use ball mount # 3593, either 1-7/8-inch ball # 19256 or 2-inch ball # 19258, and 4-pole wiring harness # 118528. This is a powered converter harness.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Q&A: Options For Replacing A Tie Down Turbo Lube 48394 Clear Oil Bath Cap
- Q&A: What Size Bolts Hold Draw Tite Hitch # 24867 to 2016 Nissan Juke
- Q&A: No Power at 12 Volt Pin In 7-Way on a 2008 Toyota Tundra
- Article: How to Measure for Trailer Hitch Drop
- Q&A: How Do I Install a Brake Controller on My 2021 Subaru Outback Wagon?
- Q&A: 2013 Nissan Juke Trailer Hitch Recommendation for Cargo Carrier
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Q&A: Anti-Rattle Device Recommendations for 1-1/4 inch to 2 inch Hitch Adapter
- Q&A: Does the Pro Series Anti-Rattle Device Fit Both 1-1/4 and 2 inch Hitches
- Article: How to Choose the Right Trailer Hitch Class
- Article: Trailer Hitch Receiver Sizes