How to Install Lippert Bolt-On Shock Mount Kit LC281255
Question:
Installing the Lippert Components Trailer Suspension - LC281255 I purchased from you awhile back. No installation instructions where provided. Your video is not detailed enough. Search internet but no luck. Please provide installation instructions. Thank you.
asked by: Scott T
Expert Reply:
I will be happy to explain how to install the shock kit # LC281255. In addition to the instructions below I have also included a picture of the actual instructions.
1. Raise trailer and jack up the axle to release pressure on the springs.
2. Remove old u-bolts and tie plate.
3. Install new tie plate with the longer side facing outward and torque the u-bolts to the specs in the instructions. NOTE: Do NOT reuse old components.
4. Compress the shock and make a mark on the inner shock where the outer shock stops.
5. Release compression. Measure the stroke and make a mark on the inner shock that is one half of the stroke length.
6. Measure the shock length when the shock is compressed to the halfway mark made in Step 5.
7. Lower the trailer back down onto tires and level so the equalizer(s), if equipped, are parallel to the frame and there is a full load on the springs.
8. Make a measurement perpendicular to the shock mounting lip on the tie plate that is the same distance measured in Step 6 + 2” and make a mark on the I-beam parallel to the shock mounting lip on the tie plate. NOTE: Mount shocks pointing outwards (away from the shackle kit, equalizer and/or center point) to get the best performance from the shocks. NOTE: Dry fit the shock to be sure it does not exceed a 45 degree angle or it will not function.
9. Align the bottom of the extended portion of the upper shock mounting bracket to the mark made on the I-beam in Step 8 and drill 11/32” pilot holes.
10. Use the 3/8” self-tapping bolts to secure the upper shock mounting bracket to the I-beam.
11. Remove nut, washer and rubber grommet from both sides of the shock.
12. Place the shock into the shock mounting lip on the tie plate and compress it to fit into the upper mounting bracket.
13. Apply the rubber grommet, washer, and nut (in that order) and tighten to secure the shock.
NOTE: Do NOT over-tighten. Tighten until the rubber grommet increases diameter equal to the washer.
Product Page this Question was Asked From
Lippert Bolt-On Shock Kit w/ Heavy Duty Gas Shocks - 3,500-lb (2-3/8") Axle
- Trailer Suspension Parts
- Leaf Spring Enhancement System
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Shocks
- Round Axle - 2-3/8 Inch
- Single Axle
- Lippert
more information >
Continue Researching
- Shop: Lippert Bolt-On Shock Kit w/ Heavy Duty Gas Shocks - 3,500-lb (2-3/8") Axle
- Search Results: 205/75/15 load range e
- Search Results: 281281
- Shop: Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Galvanized
- Shop: Bulldog Replacement Pipe Mount for Swivel Jacks - 2-7/8" Female - Weld On - 7/8" Pull Pin
- Search Results: 12k trailer jack
- Search Results: trailer jack
- Search Results: trailer jack pipe mount
- Search Results: 10k trailer jack
- Shop: Round Snap Ring Swivel Jack w/ Footplate - Weld On - Zinc - Topwind - 10-1/2" Travel - 2K
- Shop: Custer 4-LED Strobe Light or Running Light - 3-Wire Pigtail - Red
- Shop: Dexter Trailer Hub and Drum Assembly for 5,200-lb to 7,000-lb Axles - 12" - 8 on 6-1/2
- Search Results: tjb~2001~z
- Shop: Trailer Hitch
- Shop: Replacement Trailer Hub Bearing - 2788
- Shop: Trailer Wiring
- Q&A: How to Install Lippert Bolt-On Shock Mount Kit with Heavy Duty Gas Shocks for 3 Inch Axles
- Video: Review of Lippert Trailer Leaf Spring Suspension - Bolt-On Shock Mount Kit - LC281255
- Q&A: Can Lippert Bolt On Trailer Shock Kit be Used on Trailer with Axles Above Springs
- Q&A: Can the Lippert Components Bolt-On Shock Mount Kit # LC281281 be Installed on Tandem Axle Trailer
- Video: Dexter Trailer Springs Over-Under Conversion Kit Installation K71-384-00
- Shop: Suspension Enhancement
- Video: Ventline Trailer Roof Vent Installation
- Video: Ventline Ventadome Replacement Screen Review
- Video: Ventline RV Vents and Fans BVC0573-31 Review
- Video: Ventline RV Vents and Fans BVA0444-32 Review
- Q&A: Does Lippert Shock Kit Fit Enclosed Trailer with Boxed Frame
- Q&A: How to Position the Lippert Shocks on a Single Axle Trailer
- Video: Roadmaster Comfort Ride Shock Absorbers Installation - 2021 Coachmen Apex Ultra-Lite Travel Trailer
- Q&A: Should Lippert Bolt On Shocks LC281255 Be Added To Both Axles Of 7' x 14' Tandem Axle Trailer?