Hub that Fits Same Spindle as Hub/Drum # 8-219-4UC3
Question:
I had a .wheel bearing go out on my hay trailer. It need a hub assembly not a drum this hub goes on the idler axle. This part number 8-219-4UC3 has the right bearings grease seal and lug nuts, but what I am unsure about is if this part number is for a hub drum assembly or just the hub. Can you please clarify this for me so I can get this hub and bearings,races seals and all the necessary pieces so I can get this trailer back in service. Thanks,
asked by: Glen M
Expert Reply:
The part # 8-219-4UC3 is a hub/drum but for a hub without the drum that would fit the same spindle you would want the part # 8-231-50 and then would need to provide the seal part # RG06-090 as it does not come with seals and this is the same as what you need.
Products Referenced in This Question
Dexter Trailer Hub and Drum Assembly for 5,200-lb to 7,000-lb Axles - 12" - 8 on 6-1/2
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Standard
- 25580
- 14125A
- For 5200 lbs Axles
- For 6000 lbs Axles
- For 7000 lbs Axles
- 1/2 Inch Stud
- 8 on 6-1/2 Inch
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- 17 Inch Wheel
- 17-1/2 Inch Wheel
- Dexter
more information >
Trailer Hub for 5,200-lb to 7,000-lb Axles - 8 on 6-1/2 - Galvanized
- Trailer Hubs and Drums
- Hub
- Standard
- 25580
- 14125A
- For 5200 lbs Axles
- For 6000 lbs Axles
- For 7000 lbs Axles
- 1/2 Inch Stud
- 8 on 6-1/2 Inch
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- 17 Inch Wheel
- 17-1/2 Inch Wheel
- Dexter
more information >
10-10 Grease or Oil Double-Lip Seals - Qty 2
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 2.125 Inch I.D.
- 3.376 Inch O.D.
- TruRyde
more information >
Product Page this Question was Asked From
Dexter Trailer Idler Hub Assembly - 5,200-lb, 6,000-lb and 7,000-lb Axles - 12" - 8 on 6-1/2
- Trailer Hubs and Drums
- Hub
- Standard
- 25580
- 14125A
- For 5200 lbs Axles
- For 6000 lbs Axles
- For 7000 lbs Axles
- 1/2 Inch Stud
- 8 on 6-1/2 Inch
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- 17 Inch Wheel
- 17-1/2 Inch Wheel
- Dexter
more information >
Continue Researching
- Q&A: Replacement Hub/Drum and Brake Assemblies for Trailer with AL-KO 8460 Hubs
- Q&A: What Brake Fluid Is Required For Hydrapro Alpha G-1600X Electric Over Hydraulic Actuator Disc Brakes
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Q&A: Comparing Rotor-Only and Hub/Rotor Disc Brake Conversion Kits
- Q&A: Parts Needed to Add Disc Brakes to Trailer with Dexter 12K Axles w/ Electric Drum Brakes
- Q&A: Can I Have Hydraulic Brakes On One Axle And Electric Brakes On The Other Axle On Tandem Trailer
- Q&A: What is the Difference Between Kodiak Disc Brake Kit # K2R712 and # K2HR712
- Q&A: Comparing the HydraStar Hydraulic Actuator and the Titan BrakeRite Hydraulic Actuator
- Article: Most Popular Wheel Bearings
- Article: Brake Controller Installation: Starting from Scratch
- Article: Trailer Wiring Diagrams
- Article: Slipper Spring Trailer Suspension System Review
- Article: Where to Position the Trailer Axle?
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs