Is there a Block Heater for a Kioti CK20 Tractor with a Daedong 3 cylinder 0.9 Liter Diesel Motor

Question

Question:

Kioti 2o horse 3 cyl diesel kc-20. Can you please help me with a part number Thank you

asked by: Jon

0

Expert Reply:

Your tractor uses a Daedong 0.9 liter motor. I checked with Kat's haters and they do not offer a custom fit heater for any of the Daedong motors. But we do over oil/transmission pan pad heaters such as # KH24050 and others. I have included a link to them for you.

expert reply by: Michael H

0

Answer 1

The Kat's Heaters Thermostatically Controlled Circulating Tank Heater - 120V - 1,500 Watts #KH13150 must be positioned vertically for the thermosiphon to work correctly. The plug should be pointed down and the coolant flow arrow pointed up.…

view full answer...

Answer 2

I checked with Kat's and for the Perkins 1104 Engine on your Kioti Tractor they have the Frost Plug Style Engine Block Heater #KH11619 as being a confirmed fit. This will simply replace the existing frost plug in the engine block and…

view full answer...

Answer 3

Yes, the Kat's Heaters Lower Radiator Hose Heaters are available in several different sizes and thermostat settings which I have attached for you below. 175 Degrees Fahrenheit: 2-1/4" - part #KH14825 2-1/2" - part #KH14850…

view full answer...

Answer 4

I have attached the installation instructions of the Kat's Heaters Thermostatically Controlled Circulating Tank Heater part #KH13200 for you. Most vehicles on the road today run a 50/50 mix of water and antifreeze therefore you should not need to…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Is there a Block Heater for a Kioti CK20 Tractor with a Daedong 3 cylinder 0.9 Liter Diesel Motor

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching