How To Determine Which Electric Brakes Will Fit On A 6x12 Utility Trailer Without Any Brakes
Question:
I have a utility 6x12 trailer I recently purchased. I want to install electric brakes on it. How do I determine which brakes to put on it?
asked by: C.Ramsey
Expert Reply:
I will need the bearing part numbers and the grease seal part number from your trailer so we can determine the correct hub drum assembly that is needed to install electric brakes on your trailer. The numbers needed for your bearings will be imprinted on the bearings and seals themselves. You would disassemble the hub and read the numbers off the bearings and seals. Remember which order they go in. Some trailer hubs have different size bearings on the inner and outer sides of the hubs. I have also included a link to a page on removing and repacking bearings.
To determine which brakes to use on your utility trailer you will need to use the weight capacity of the axle (2,000 lbs., 3,500 lbs.), the wheel bolt pattern (4 on 4, 5 on 4-1/2), and the wheel size (13 inch, 14 inch) then you can pick the brakes that will fit your hub drum assembly. I am including a link to a page on how to measure the bolt pattern on your wheel.
You will need to use a hub drum that will have the hub built into the drum. The etrailer.com 10 Inch Electric Brake Assembly - Left Hand, part # AKEBRK-35L, you have referenced is for a 3,500 lbs. axle with a 5 on 4-1/2 inch bolt pattern. This brake assembly will use the etrailer.com Trailer Hub & Drum Assembly, part # AKHD-545-35-K.
The brake assembly would mount to a brake mounting flange on your axle. If a brake mounting flange is needed you will need to have to install the Redline Brake Mounting Flange # 4-35. This flange would have to be welded, by a certified professional welder, to the end of the axle and provides a mounting place for the brake assembly.
If you want to get back to me with all of that information I will be able to help you choose the correct setup to install electric brakes on your 6x12 utility trailer.
Products Referenced in This Question
Brake Mounting Flange for 2-3/8" Round Axle
- Accessories and Parts
- Trailer Brakes
- Disc Brakes
- Electric Drum Brakes
- Hydraulic Drum Brakes
- Brake Mounting Flange
- 10 Inch
- 2-3/8 Inch Diameter Axle
- Redline
more information >
Electric Trailer Brake Assembly - 10" - Left Hand - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Electric Drum Brakes
- LH
- 3500 lbs
- Brake Assembly
- Manual Adjust
- 10 x 2-1/4 Inch Drum
- etrailer
more information >
Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Standard
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Product Page this Question was Asked From
Electric Trailer Brake Assembly - 10" - Left Hand - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Electric Drum Brakes
- LH
- 3500 lbs
- Brake Assembly
- Manual Adjust
- 10 x 2-1/4 Inch Drum
- etrailer
more information >
Continue Researching
- Q&A: Can Electric Brakes be Used on a Boat Trailer
- Q&A: Which Replacement Electric Brakes For 10" Drum Stamped KA90831
- Article: Trailer Wiring Diagrams
- Q&A: Which Brake Assembly Does Part Numbers B10E-21 & B10E-22 Correspond to?
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: Most Popular Wheel Bearings
- Q&A: Both Left Side Brakes Work on Trailer but No Right Side Brakes
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Q&A: Where To Connect Two White Wires From Brakes on Trailer Axle
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision
- Q&A: Replacement Dexter Brake Assemblies for 36-19 Assemblies
- Q&A: How to Bleed Brakes With Dexter Zinc-Plated Brake Actuator
- Article: Testing Trailer Brake Magnets for Proper Function
- Article: How to Charge a Trailer Battery While Driving: 3 Common Problems (And How to Fix Them)