Recommended Parts To Convert Hydraulic Drum To Disc Brakes On EZ-Loader Trailer
Question:
I have a boat trailer EZ loader model #TE2L 102B 17-20/22 4000 Serial #1ZEAAZRT2DA000582. Trailer capacity 400lb, oil bath bearing system. Coupler Triler Buddy model A-60/A-75 hydronic actuator. Spindle size ? This is the bearing inner #250-031477, outer #250-031474 and seal #350-031468. Wheels and tires 13foot rims, 175/80/13 can I keep these wheels with a disk brake system. Let me know if you require more information to recommend all parts required to convert a drum brake system to a disk brake system.
asked by: Jean-Guy
Expert Reply:
In my research I found that the numbers you mentioned for the bearings you have on your trailer match a bearing kit we offer. The kit for one wheel is part # BK2-100. This is designed for a 3500-lb axle. The kit includes inner and outer bearings, race, seal, washer and cotter pin.
The disc brake kit I recommend is the Kodiak Kit, part # K2HR35D. The wheel size this kit will work with is 13 inches or bigger. The hub/rotor included with this kit has a 5 on 4-1/2 bolt pattern for the wheels so you will want to make sure the bolt pattern for your wheels is the right pattern. I have attached a helpful article that explains how to measure the bolt pattern of your wheels.
A coupler designed for drum brakes usually has a 1000 psi rating where a disc brake actuator has a rating of 1,500 or 1,600 psi. You may be able to just replace the master cylinder to a higher rated one that can work with disc brakes. We do not offer a master cylinder designed for your actuator.
Products Referenced in This Question
Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- Bearing Kits
- Bearing L44649 and L68149
- Race L68111 and L44610
- 3500 lbs Axle
- etrailer
more information >
Product Page this Question was Asked From
Kodiak Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Disc Brakes
- LH
- RH
- 3500 lbs
- Brake Assembly
- 5 on 4-1/2
- Hub and Rotor Assembly
- Kodiak
more information >
Continue Researching
- Q&A: Will 3,500 lb Kodiak Disc Brake Kit Fit 2012 EZ Loader Boat Trailer
- Article: Parts Needed to Add Hydraulic Disc Brakes to a Trailer
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Article: Most Popular Wheel Bearings
- Q&A: How to Convert Drum Brakes to Disc Brakes on a 2005 Boat Trailer
- Q&A: How to Determine if Trailer has 84 Spindle to Pick Out Replacement
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision
- Q&A: Replacement for Global Direct GDC80 Brake Actuator
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Article: Wiring Trailer Lights with a 5-Way Plug (It's Easier Than You Think)
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Q&A: Why Were The Kodiak 204 Calipers and Pads Discontinued?
- Q&A: How do etrailer Brand Trailer Brake Assemblies Compare to Lippert and Dexter
- Q&A: How To Choose Correct MORryde Shackle Upgrade Kit