Will Curt Hitch part # C11041 Fit a 1997 Ford Mustang GT

Question

Question:

According to your web site you have a hitch to fit a 97 Mustang V8. Have you installed one and would it take a Motorcycle trailer.

asked by: Jim

0

Expert Reply:

The Curt Hitch # C11041 is only a confirmed fit for the V6 models. It will not work on the V8 models of the 1997 Ford Mustang so it would not fit your GT which has a V8.

expert reply by: Jameson C

0

Answer 1

The #C11041 that you referenced only fits the V6 models so it would not work for you. It is the only hitch that we carry for 2000 Mustangs. If you are interested in carrying bikes with your Mustang, you could use a trunk mounted rack like the Saris…

view full answer...

Answer 2

For a hitch for your 2000 Ford Mustang GT V6 you will want the Curt Hitch part #C11041. The correct drill bit you will want to make the install easier is the part #40110 that you referenced. I attached an install video for you to check out as well.…

view full answer...

Answer 3

We have just what you are looking for! You need the Draw-Tite Trailer Hitch Receiver #24687 which is a confirmed fit for your 2001 Mustang GT. If you are planning on using your trailer hitch receiver to tow a trailer you will also need a vehicle…

view full answer...

Answer 4

The Curt #C11041 is a great choice for your 1994 Ford Mustang. This Curt hitch has strong welds and a thick powder coat finish which promotes a longer-lasting life. Installation instructions have been linked for your 2004 Mustang for you to check…

view full answer...

Answer 5

You will not be able to install a roof rack on a 2000 Ford Mustang GT convertible. The soft top prohibits installation of any kind of roof rack. For trailer hitches, Draw-Tite and Hidden Hitch are owned by the same company and the hitches even share…

view full answer...

Answer 6

The Curt trailer hitch #C11041 is for Mustangs with V6 engines since your GT is a V8, we don't have a hitch for you.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Will Curt Hitch part # C11041 Fit a 1997 Ford Mustang GT

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching