Weight Distribution System Recommendation for a Trailer with 750 lbs of Tongue Weight
Question:
The trailer Im looking to buy has a 750lb young weight and a gross weight loaded of 9500lbs. Should I purchase a WD/Sway control solution that is rated at just a little better than those numbers like the Reese 66087 or is bigger and beefier better?
asked by: Thomas S
Expert Reply:
The best way to pick out a weight distribution system is to base it off of the loaded tongue weight of the setup when it is loaded and ready to tow. This figure also includes the weight of any cargo behind the rear axle of the tow vehicle. I attached a help article on determining tongue weight for you to check out as well. You will want the loaded tongue weight of your setup to fall right in the middle of the tongue weight range of the system you use.
For your loaded tongue weight figure of 750 lbs the part # RP66087 would technically work as it has a tongue weight range of 400-800 lbs but you would be right at the top of it's range. So if there was any chance you would end up with more tongue weight it wouldn't be an ideal solution for you.
A better option would most likely be the part # RP66088 which has a tongue weight range of 600-1,200 lbs and has the same dual cam sway control that fights sway before it starts. I attached an install video for this kit as well.
For a 2 inch ball you would want part # A-90 and for a 2-5/16 inch ball # 19286.
Products Referenced in This Question
2-5/16" Hitch Ball - 1-1/4" Diameter x 2-3/4" Long Shank - Chrome - 12,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2-5/16 Inch Diameter Ball
- 2-3/4 Inch Shank Length
- 1-1/4 Inch Diameter Shank
- 12000 lbs GTW
- Class IV
- Class V
- Draw-Tite
more information >
2" Hitch Ball - 1-1/4" Diameter x 2-5/8" Long Shank - Chrome - 10,000
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-5/8 Inch Shank Length
- 1-1/4 Inch Diameter Shank
- 10000 lbs GTW
- Class IV
- Class V
- CURT
more information >
Product Page this Question was Asked From
Strait-Line Weight Distribution System w Sway Control - Round Bar - 10,000 lbs GTW, 800 lbs TW
- Weight Distribution Hitch
- WD With Sway Control
- Some Sway
- Includes Shank
- Electric Brake Compatible
- Fits 2 Inch Hitch
- Allows Backing Up
- 500 lbs
- 600 lbs
- 700 lbs
- Reese
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Will The Reese Dual Cam II Weight Distribution System # RP65FR Fit 2023 GD Imagine XLS 22RBE?
- Q&A: Best Weight Distribution and Sway Control Option for 1998 Durango
- Q&A: Does the Strait-Line Weight Distribution Hitch Allow You to Turn and Back Up at the Same Time?
- Q&A: Were Cams of Reese Dual Cam III Upgraded from Previous Version
- Q&A: Where to Mount Spring Bar Support Brackets on Curt TruTrack Weight Distribution System # C17499
- Q&A: Which System Is Best Between The Curt TruTrack & The Equal-i-zer Weight Distribution System?
- Article: Which Sway Control Hitch is Right For Your Trailer?
- Q&A: Fastway e2 or Reese Steadi-Flex Weight Distribution Hitch For 8,500 lb Travel Trailer
- Article: Best Camper Jacks
- Article: Determining Trailer Tongue Weight
- Article: How to Install a Weight Distribution Hitch (With Pictures & Video)
- Article: 5 Tips to Confidently Choose Your Weight Distribution Hitch
- Article: 2 Steps for Finding the Right Weight Distribution Hitch Size
- Article: 5 Things to Know About Weight Distribution Hitches