Installation Hardware Included with Draw-Tite 75527 Class III Trailer Hitch for 2016 Toyota Tundra

Question

Question:

Does the hitches come with mounting bolts?

asked by: Brent C

1

Helpful Expert Reply:

The Draw-Tite Class III # 75527 trailer hitch does indeed include all necessary mounting hardware. If you click the provided links, you can see the installation instructions which includes a listing of the included hardware. I've also linked to an install video that I hope you'll find helpful.

expert reply by: Mike L

1

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 6

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 7

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 8

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Installation Hardware Included with Draw-Tite 75527 Class III Trailer Hitch for 2016 Toyota Tundra

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching