Can a Different Trailer Hitch be Installed on 2012 Subaru Outback without Removing Factory Hitch
Question:
I currently have a dealer installed Class I hitch installed on my outback... it comes out of the back bumper and does not hand down below. . Can I install a heavier hitch without un-installing this factory hitch?
asked by: Stan S
Expert Reply:
The factory trailer hitch on your 2012 Subaru Outback would still be in the way of an aftermarket hitch. It would have to come off of the vehicle in order to install a different hitch. Sometimes the factory hitches are welded on. If that is the case with your hitch then you will not be able to remove it.
But if it bolts on you can remove it. Then you can install Draw-Tite Class III trailer hitch # 75673. I have included a link to a video showing an example installation for you. If you plan on doing some towing I recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag.
If the ball mount kit does not have the right rise or drop to tow the trailer level, use the link I have included that explains how to measure to choose a ball mount to tow the trailer level.
And if you need a trailer wiring harness you can use # 118467 to add a 4-Way flat connector to the rear of the vehicle. I have linked a video showing how the wiring installs as well.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 600 lbs TW
- 4000 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Recommended 16' Mesh Tarp for Dump Trailer
- Q&A: What is the Estimated Installation Time for Firestone Ride-Rite Air Bags on a 2006 Ford F-250
- Q&A: Recommended Tire Clearance Between Tires on Dual Axle Trailer
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Q&A: Replacement Strut for Stabilus Lift-O-Mat on Dometic Awning
- Q&A: Is a Master Key Needed to Install or Remove a Thule Lock Cylinder
- Q&A: Can Electric Trailer Brake Kit # AKEBRK-2 be Submerged in Water
- Q&A: Equalizer Replacement Options for Dexter 13-122 Equalizer
- Article: How to Choose the Right Trailer Hitch Class
- Article: My Trailer Hitch Doesn't Fit
- Article: Best Bike Racks for Electric Bikes
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams