Will a Trailer Hitch Fit a 2016 Jeep Wrangler Sahara 75th Anniversary Edition
Question:
Will the models listed for the wrangler also fit on the sahara model with the 75th anniversary option?
asked by: Tom
Expert Reply:
The trailer hitches listed for the 2016 Jeep Wrangler will not fit Limited Edition or Special Edition models unless they have the same rear bumper as the regular Jeep Wrangler. Limited/Special edition models can have an alternate rear bumper that would interfere with installation of a hitch.
If your 75th anniversary edition has the regular Wrangler rear bumper then I recommend hitch # 13432. This is the most cost-effective hitch option for your Jeep. I have linked a video showing an example installation of this hitch for you.
If you plan on doing some towing I recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag.
If the ball mount kit does not have the right rise or drop to tow the trailer level, use the link I have included that explains how to measure to choose a ball mount to tow the trailer level.
And for trailer wiring you can use # 118416 to add a 4-Way flat connector to the rear of the vehicle. I have linked a video showing an example installation of the wiring as well.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 4000 lbs WD GTW
- 2 Inch Hitch
- 400 lbs WD TW
- No Cross Tube
- CURT
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 4000 lbs WD GTW
- 2 Inch Hitch
- 400 lbs WD TW
- No Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Equalizer Replacement Options for Dexter 13-122 Equalizer
- Q&A: Comparing Equa-Flex and Road Armor Equalizers For 2000 Forest River WIldwood W/ 5200lb Axles
- Q&A: Can 12 Volt Battery Replace Two 6 Volt Batteries
- Q&A: Replacement Electric Brakes for Dexter PR-FF SEC-FF 5.2KPR-GGSEC-GG 12X2XQ 36-89
- Q&A: Replacement 12 inch Brake Assemblies for Dexter 36-89 on Trailer
- Q&A: Comparing Curt and Tekonsha Trailer Wiring Harness for 2018 Jeep Wrangler Unlimited
- Q&A: Recommended Tire Clearance Between Tires on Dual Axle Trailer
- Article: How to Rent an RV
- Article: What Exactly is Tongue Weight?
- Article: How to Choose the Right Trailer Hitch Class
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Measure for Trailer Hitch Drop
- Article: Electric Brake Controller Installation on Dodge Ram Trucks to 2012
- Article: My Trailer Hitch Doesn't Fit