Parts Needed to Flat Tow a 2007 Nissan Titan
Question:
All I need to tow a 2007 Nissan Titan SE is the RM-501 and the 341-1 base plates. Right? What tools will I need?
asked by: Benjamin H
Expert Reply:
The two components you mentioned are important parts needed for flat towing, but there are several other things needed too.
For safety cables you can use # RM-643. The coiled design helps keep the cables off of the ground.
For lighting you can use the diode kit, # RM-15267, and not have to worry about cutting into the taillight housing. This will splice into your taillight wiring to allow your tow vehicle to control the taillight assemblies of the towed vehicle. This comes with a round 6-way connector that you will install on the front of your towed vehicle and enough coiled wire to go from there to the RV.
And finally, most states now require supplemental braking in the vehicle being flat towed. The easiest system to set up and use is the Blue Ox Patriot II, # BRK2016, that applies the vehicle brakes in proportion to how much the tow vehicle is braking. This is the safest way to stop and it reduces wear and tear on both vehicles.
Most likely you will also need a high low adapter so that the tow bar will be level when you are flat towing. I attached a link to a page that has all of the ones we carry.
I have included a couple of helpful links to our articles on flat towing for you. Be sure to consult the vehicle owners manual for more specific information on flat towing your vehicle.
The base plate kit would be the most involved install, but with basic tools it wouldn't be that hard.
Products Referenced in This Question
Roadmaster Crossbar-Style Base Plate Kit - Removable Arms
- Base Plates
- Removable Drawbars
- Hitch Pin Attachment
- Roadmaster
more information >
Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Tow Bar Wiring
- Splices into Vehicle Wiring
- Diode Kit
- Universal
- Tail Light Mount
- Roadmaster
more information >
RoadMaster 68" Single Hook, Coiled Safety Cables - 6,000 lbs
- Safety Cables
- Coiled Cables
- 68 Inch Long
- 6000 lbs GTW
- Snap Hooks
- Coated Cables
- Roadmaster
more information >
Product Page this Question was Asked From
Roadmaster StowMaster Tow Bar - Coupler Style for 2" Ball - Car Mount - 6,000 lbs
- Tow Bar
- Coupler Style
- Telescoping
- Steel
- 6000 lbs
- Fits Roadmaster Base Plates - Crossbar
- Stores on Car
- Standard
- Roadmaster
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Roadmaster Vehicle Specific Base Plates
- Q&A: Can I Use A Tow Bar With The 2" Hitch On A 2006 Ford E350 Van?
- Article: Tire TLC: How & When to Check Your RV/Trailer Tire Pressure
- Q&A: Wiring For Lights When Dinghy Towing 2015 Kia Soul
- Article: Flat Towing Package for 2018 Jeep Wrangler JL and JL Unlimited
- Article: Trailer Wiring Diagrams
- Article: The Definitive, Step-by-Step Flat Towing Setup Guide
- Article: How to Choose the Right Trailer Hitch Class
- Article: How to Choose a High-Low Adapter
- Q&A: Recommended Baseplate For A 2023 Jeep Grand Cherokee 4xe With Roadmaster Falcon 5250 Tow Bar
- Q&A: Base Plate and Tow Bar Recommendations for a 2018 Ford Focus Hatchback
- Q&A: Recommended Replacement Ladder for 2018 Thor Challenger 37 FH with Indent on Rear
- Q&A: How Does Atwood Water Heater Switch # AT91959 Get Wired
- Q&A: Recommended Base Plate for a 2014 Honda CR-V