Looking for Ball Mount with 3/4 Inch Rise or Drop
Question:
I need a 2inch hitch with a 3/4 inch . Do you have anything close? cant seem to locate one. Thanks
asked by: Steve
Expert Reply:
I'm guessing you're needing a ball mount, is that correct? Were you needing a rise or a drop?
If you're needing a 3/4 inch rise, the # D-4 ball mount would provide that. If you flip the # D-4 to the drop position, you'd have a 2 inch drop, which is as close as we can get to a 3/4 inch drop. As long as the trailer ball places the trailer within 2 inches of level, you'll be just fine. The ball mount has a 7500 lb capacity. For a Hitch Pin and Clip, # PC3, and a 1-7/8 inch trailer ball, use part # 19260 or # 63845 for a 2 inch ball.
If you have to choose between towing the trailer tongue high or tongue low, tongue high is preferable.
Products Referenced in This Question
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Ball Mount for 2" Hitch - 1" Rise, 2" Drop - 8-1/2" Long - 12,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1-1/4 Inch Ball Hole Diameter
- Steel Shank - Silver
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 12000 lbs GTW
- Class IV
- Draw-Tite
more information >
Continue Researching
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Will Linxup GPS Tracking Device Work With 4G Service
- Q&A: Comparing Linxup GPS Tracking Devices and Compatible Phone Networks
- Q&A: Difference between Tekonsha T-One and Curt T-Connector Wiring Harness for 2007 Toyota Sienna
- Q&A: Extreme Off-Road Swing-Up Jack for a T@B 400 Tear Drop Trailer
- Q&A: Overall Length When Retracted of the Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Location of Six-Digit PIN for Pairing Curt Echo Brake Controller
- Q&A: Curt C51180 Echo Wireless Brake Controller Drains Vehicle and Trailer Battery
- Article: Which Hitches are Made in the USA
- Article: How to Measure a Trailer Axle
- Article: Steel vs. Aluminum Ball Mounts
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Article: Hitch Adapters and Extenders