Removing Existing Brake Controller and Installing Tekonsha Prodigy P2 90885 on 2012 Nissan Frontier
Question:
Hi. I currently have the following items installed in my 2012 Nissan Frontier: 118266 Vehicle Wiring Harness with Relays and 7-Way Trailer Connector C51110 Curt Venturer Trailer Brake Controller - 1 to 3 Axles - Time Delayed C51382 Curt Custom Wiring Adapter My 2010 Ford Flex has the Prodigy P2 controller. If I wanted to put the P2 in my Nissan what additional items would I need to do the install besides the P2 wiring harness for the Nissan? Understanding that I need to remove the Curt Controller and wiring but do I need to remove the relays from the Curt install? Thanks.
asked by: Paul
Helpful Expert Reply:
Good choice going with a proportional controller like the Prodigy P2, part # 90885. A proportional controller uses a built in accelerometer to determine how fast the tow vehicle is braking. It will then send the appropriate amount of voltage to the trailer brakes so the vehicle and trailer brake at the same rate for safe and predictable braking. Although the Curt Venturer is a good piece of equipment, it uses the older time-delayed technology that will always send the same amount of preset voltage to the brakes, regardless if its an all-out panic stop or a quick jab to the brake pedal.
You'll need the controller itself and the appropriate brake controller wiring adapter, which is part # 3050-P. I'd also recommend the pocket mount, part # 7686.
The relays you speak of power up the 12-volt accessory circuit to the 7-way and the right turn/brake lamp and left turn/brake lamp signals to the trailer. The relays will have no bearing on the function of the brake controller and would stay in place right where they are.
The install will be very simple, it should only take a few minutes. I've linked you to some product description videos that I hope you'll find helpful.
Products Referenced in This Question
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Nissan and Infiniti
- Accessories and Parts
- Trailer Brake Controller
- Wiring Adapter
- Plugs into Brake Controller
- Vehicle Specific
- Tekonsha
more information >
Mounting Pocket for Tekonsha Prodigy Proportional Brake Controller
- Accessories and Parts
- Trailer Brake Controller
- Mounting Hardware
- Brackets
- Tekonsha
more information >
Product Page this Question was Asked From
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Brake Controller Installation: Starting from Scratch
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: Trailer Wiring Diagrams
- Article: How to Choose the Right Trailer Hitch Class
- Article: How to Install a Brake Controller on Chevrolet / GMC 1999-2006 Pickups
- Article: Most Popular Wheel Bearings
- Q&A: Brake Controller Recommendation for a Truck with Air Brakes and a Trailer with Electric Brakes
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Parts Needed to Install 7-Way/4-Way on 2024 Kia Telluride with LED Taillights
- Q&A: How do I Tell if the Brake Controller is Bad
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Q&A: How Is Spring Bar Tension Set Up with Trailer Weight Distribution System