Can The Draw-Tite Ball Mount, # 36065, Be Turned Over And Used As A Drop On a Mercury Mountaineer
Question:
Merc Mountaineer with a 1 1/4 receiver, towing a small trailer for a Quad, because the Merc is high, need a , another part offers both a rise and but is 10$ more plus need a pin with that order.......
asked by: Jerry
Expert Reply:
A 1-1/4 inch hitch receiver is either a Class I or Class II hitch. All Class I and Class II can only use the ball mounts that are recommended for that vehicle.
For safety reasons, if you have to change the rise or drop from the recommended ball mount, then the manufacturer does not recommend to tow that trailer with the Class I or Class II hitch on your vehicle.
We have Class III hitches available for Mercury Mountaineers that will bolt on underneath the OEM 1-1/4 hitch. The Class III hitch will allow you to use ball mounts of different rise or drop. Both hitches cannot be used at the same time.
If you have a 2002-2005 Mercury Mountaineer 4-Door you can use the Draw-Tite Trailer Hitch, # 75132. If you have a 2006-2010 Mercury Mountaineer you can use the Draw-Tite Trailer Hitch, # 75437.
Both of those hitches are 2 inch Class III rated hitches.
The Class III hitches will be mounted underneath the OEM hitch so you will have to measure to see how much rise or drop ball mount you would need.
You will also need either the 2 inch hitch ball, # 19247, or a 1-7/8 inch hitch ball, # 19260, depending the coupler size on your trailer. Also the pin and clip, # PC3.
I am sending a link that will show you how to choose a correct ball mount and how to measure the rise or drop you will need.
Products Referenced in This Question
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 8000 lbs WD GTW
- 2 Inch Hitch
- 800 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 8000 lbs WD GTW
- 2 Inch Hitch
- 800 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Drawbar for 1-1/4" Hitches - 5" Rise - 10" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Rise - 5 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Measure for Trailer Hitch Drop
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Trailer Hitch Receiver For 2023 Hyundai Elantra Hybrid
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Article: How to Choose the Right Trailer Hitch Class
- Article: Trailer Tire Sizing
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: How to Upgrade Trailer with 45 MPH Speed Rating for Highway Speeds
- Q&A: Recommended Hitch for a 2023 Hyundai Elantra
- Q&A: Recommended Hitch for a 2023 Hyundai Elantra
- Article: The 5 Best Trailer Drop Hitches You Can Buy
- Q&A: Recommended Wiring Harness For 2020 Toyota Rav4 LE Hybrid
- Q&A: What is the Height With and Without Rise on Ball Mount for 2016 Ford Fusion
- Q&A: What is the Difference Between a Class II and a Class III Hitch?