Electric Over Hydraulic Trailer Brakes not Working w/2015 Chevy Silverado Factory Brake Controller
Question:
I have a 2015 Chevy 2500hd. I have a built in integrated brake controller on it. When I press the brake peddle the brakes will not work on the trailer. If I only use the brake controller lever then the brakes will work. I also had a friend try it with his 08 chevy with aftermarket controller and he had the same problem. I also tried a brake controller and bypassed the blue wire directly to the trailer plug and get the same issue. Thank you for your time.
asked by: Terry H
Expert Reply:
First, on the integrated trailer brake controller on your 2015 Chevy Silverado 2500, make sure that it is in electric over hydraulic mode. Your friend's brake controller and possibly the aftermarket one that you used may not have been compatible with electric over hydraulic brakes. Only certain controllers are, such as the P2, # 90885.
There could also be a problem with the trailer, specifically, the actuator. Below are the troubleshooting tips you can try:
1. Verify that the trailer and tow vehicle are wired according to the electrical schematic shown in “Electrical Requirements”.
2. Re-bleed the trailer brakes. Any air in the trailer brake system causes brake delay
3. If the trailer is equipped with drum brakes, re-adjust the drum brakes to the trailer manufacturer's recommended running clearance.
4. Trailer wiring that is too small can cause slow response.
5. Slow response can be caused by brake line restrictions. The trailer brake lines must be at least 3/16” in diameter. Steel tubing is preferred over flexible hoses.
6. Check to see if the white ground wire runs directly to the tow vehicle ground. IT MUST NOT BE GROUNDED TO THE TRAILER ONLY. IT IS IMPORTANT THAT THIS GROUND WIRE RUNS DIRECTLY TO THE TOW VEHICLE'S BATTERY GROUND. NO EXCEPTIONS.
7. Detach all wires from the Dexter Axle E/H unit leaving only the blue, black, white and yellow wires. It is important that the unit is disconnected from any other wires going to the towing vehicle or breakaway switch and breakaway battery. Failure to do so may result in a faulty test.
8. Using a 12 volt battery, connect the white wire to the negative (-) terminal of the battery.
9. Connect the black wire to the positive (+) terminal of the battery. The motor should not run. If the motor runs, the unit may be defective.
10. Leave the white wire connected to the negative (-) terminal of the battery.
11. Connect the blue and black wires together to the positive (+) terminal of the battery.
12. The motor should run and the unit should pressurize
13. If this does not occur, the unit may be defective.
14. Leave the white wire connected to the negative (-) terminal of the battery.
15. Connect only the yellow wire to the positive (+) terminal of the battery.
16. The motor should run and the unit should pressurize.
17. If this does not occur, the unit may be defective.
18. If the unit checks OK, reconnect the wires leading to the trailer plug and repeat steps 9 through 14 at the trailer plug. If you do not get the same results as before, the problem is in the trailer wiring or the electronic brake controller.
Using the breakaway system to troubleshoot a unit that is not operating correctly.
1. With a fully charged breakaway battery and trailer plug disconnected, pull the breakaway switch on the trailer.
1. If the unit runs and builds pressure, the breakaway system is functioning properly.
2. If the unit runs and builds pressure when the breakaway switch is pulled but will not function under normal operating conditions, the problem mot likely is a defective in-cab controller or defective wiring between the tow vehicle and Dexter E/H actuator.
3. If the unit runs but will not build pressure when breakaway switch is pulled, the Dexter E/H unit may be defective.
4. If the unit does not run, measure the DC voltage between the white wire and the yellow wire. If the voltage is less than 12 volts, either the breakaway switch or the breakaway wiring is defective.
5. After completing the above steps, reset the breakaway switch and reconnect the trailer plug.
Trailer brakes not aggressive enough
1. Increase the gain setting on the in-cab electronic brake controller.
2. Check brake adjustment.
Products Referenced in This Question
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Product Page this Question was Asked From
Dexter DX Series Electric Over Hydraulic Brake Actuator for Disc Brakes - 1,600 psi
- Brake Actuator
- Electric-Hydraulic Brake Actuator
- 1600 psi
- Disc Brakes
- Dexter
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Brake Controller
- Shop: Dexter DX Series Electric Over Hydraulic Brake Actuator for Disc Brakes - 1,600 psi
- Shop: Dexter DX Series Electric Over Hydraulic Brake Actuator for Drum Brakes - 1,000 psi
- Video: Trailer Brake Controller Installation - 2012 Chevrolet Silverado 90195
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Q&A: Factory Brake Controller on 2008 Silverado Works w/ Electric Over Hydraulic Actuator
- Shop: Curt Echo Under-Dash Bluetooth Brake Controller w/ OneControl App - 1 to 4 Axles - Proportional
- Shop: Redarc Tow-Pro Liberty Brake Controller - Dash Knob - 1 to 2 Axles - Proportional
- Shop: Tuson DirecLink Base Model Trailer Brake Controller - 1 to 4 Axles - Proportional
- Shop: Redarc Tow-Pro Elite Brake Controller - Dash Knob - 2 Braking Modes - 1 to 3 Axles - Proportional
- Q&A: Installing Prodigy P3 Brake Controller in 2008 Chevy Silverado
- Q&A: Adapter for Integrated Brake Controller of 2020 GMC Sierra 3500 w Electric Over Hydaulic Actuator
- Video: Full Disc Brake Conversion Installation - 2020 Jayco Pinnacle Fifth Wheel
- Search Results: hba~cam
- Video: Hydrastar Brake Actuator HBA-CAM Review
- Shop: Suspension Enhancement
- Q&A: Can Two Friction Sway Control Units Be Used on a Camper Trailer
- Q&A: Wiring Configuration For 7-Way Vehicle And Trailer Connectors
- Search Results: 3500 lb axle bearings
- Search Results: dexter
- Search Results: dexter electric over hydraulic
- Search Results: brake rite
- Search Results: titan actuator
- Q&A: Will the Hydrastar Adapter for Factory Brake Controllers Work with a 2015 GMC Sierra
- Q&A: Will the HydraStar Electric Over Hydraulic Actuator Work With 2018 Chevy Brake Controller
- Video: HydraStar Electric Over Hydraulic Disc Brake Actuator Installation - 2017 Grand Design Solitude Fift
- Video: Review of Dexter Axle Brake Actuator - EOH Actuator Adapter Module - DX35FR
- Article: Installing an Electric Brake Controller on 2007-2013 GM Full-Size Truck or 2007-Present GM SUV
- Article: Trailer Wiring Diagrams
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision