Hitch Extender and Recommended Locks Compatible with Class I Trailer Hitch
Question:
Can you please tell me what the distance is from the innermost edge that will drop into my existing 1-1/4 inch receiver to the center of the closest hole that will secure it? I think its 1-1/2inch from the diagram but want to make sure. Also, what is the diameter of this hole/what size locking pin is needed, and can you suggest a strong locking pin/combo for it?
asked by: Bill S
Expert Reply:
The distance from the hitch pin hole center on end that slides into the hitch receiver to the nearest end of extension # hes6 is approximately 1-1/2 inches. I assume you are asking this because you have a Class I trailer hitch. It will fit a Class I trailer hitch.
The pin holes are standard size for 1-1/4 inch accessories, 1/2 inch. Tow Ready lock # 5200 is the most popular standard hitch lock for 1-1/4 inch hitches. But I like our etrailer.com lock # e98879 because it will be flush against the hitch or accessory and has a cover for the key hole to keep out debris and moisture.
Please note that the use of an extension will reduce the tongue weight capacity of the hitch by 50 percent. The extender has a 175 pound capacity itself so if the reduced capacity of the hitch is lower you will still go by the lower amount. If the reduced capacity is greater than 175 pounds then you are still limited to 175 pounds.
Products Referenced in This Question
Trailer Hitch Receiver Lock - Padlock Style for 1-1/4" Trailer Hitch Receiver
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Unique
- Chrome
- Fits 1-1/4 Inch Hitch
- Bent Pin
- 3-1/8 Inch Span
- Tow Ready
more information >
etrailer Trailer Hitch Receiver Lock for 1-1/4" Hitches - Flush - 2-1/8" Span - Chrome
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Alike
- Chrome
- Fits 1-1/4 Inch Hitch
- Flush Pin
- 2-1/8 Inch Span
- etrailer
more information >
Product Page this Question was Asked From
CR Brophy Hitch Extender for 1-1/4" Hitch Receivers - 5-3/4" Long
- Hitch Adapters
- Hitch Extender
- Bike Racks
- Cargo Carriers
- Hitch Mounted Accessories
- Trailers
- 6 Inch Extension
- Fits 1-1/4 Inch Hitch
- 1750 lbs
- Brophy
more information >
Continue Researching
- Article: My Trailer Hitch Doesn't Fit
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Hitch Receiver Sizes
- Article: How to Choose the Right Trailer Hitch Class
- Article: Trailer Wiring Diagrams
- Q&A: Comparing the Yakima HoldUp and Yakima HoldUp EVO
- Q&A: Does the Kuat NV 2.0 Work with Bikes with Fenders?
- Q&A: Recommended Bike Rack Compatible With Bikes With Front Fenders
- Article: How to Choose a Bike Rack for a Sedan or Hatchback
- Article: How to Choose a Hitch-Mounted Bike Rack
- Q&A: Is a 1-1/4 to 2 Inch Trailer Hitch Receiver Adapter Recommended for Use with a 2 inch Cargo Carrier
- Q&A: Largest Rhino-Rack Pioneer Platform Rack for a 2013 Toyota FJ Cruiser
- Q&A: Will The Rhino Rack Rooftop Tent Brackets For Pioneer Platforms Work With The iKamper 2.0
- Article: Best Bike Racks for Electric Bikes