Hanger Kit Recommendation for a Tandem Axle Trailer
Question:
I have a tri-axle trailer that I would like to convert to a tandem axle. The current hanger heights are 3.25, 2,2,3.25 F,C,C,R. Will the APT5 work? Can I just install the new hangers in the current positions of the two center and the rear hanger?
asked by: Brian C
Expert Reply:
Yes, the Tandem Axle Hanger Kit part # APT5 would work well for you as a tandem axle hanger kit. The hangers are all 3-1/4 inches tall so they should work just fine.
I attached a review video and a help article on trailer suspension for you to check out as well.
To determine the location for the front and rear hangers on your tandem axle trailer you will first need to make sure that you have the correct center point for your equalizer hanger.
The center point of your equalizer hanger needs to be located where you will have 60 percent of the frame of the trailer in front of the center of the equalizer hanger and 40 percent behind the center of the equalizer hanger. For example, if the trailers frames length is 18 feet, then the center-line location for the equalizer hanger will be 10.8 feet from the front of the trailer and 7.2 feet from the back.
This is where to start with when picking out axle locations for a tandem axle trailer. You will need to determine the tongue weight of the trailer and then check out the picture I attached if the tongue weight is anything other than 10 percent of the total trailer weight.
Product Page this Question was Asked From
Tandem-Axle Trailer Hanger Kit for Double Eye Springs - 3-1/4" Tall Front/Center/Rear
- Trailer Suspension Parts
- Hangers
- Suspension Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- Tandem Axle
- etrailer
more information >
Continue Researching
- Shop: Tandem-Axle Trailer Hanger Kit for Double Eye Springs - 3-1/4" Tall Front/Center/Rear
- Shop: Triple-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front/Rear/Center
- Shop: etrailer Rust-Resistant 4-Leaf Double Eye Spring for 5K Trailer Axles - 25-1/4" Long - Dacromet
- Shop: Grease Cap, 1.99" OD EZ Lube Drive in with Plug - Qty 2
- Shop: Mounting Nut for 7" and 10" Brake Assemblies - 7/16" Diameter - Zinc Plated
- Shop: Wet Equalizer Bolt with Locknut and Grease Zerk for Double-Eye Springs - 3" Long
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Search Results: grease cap
- Search Results: 4000 lb axle
- Search Results: axle
- Search Results: shackle
- Search Results: spring hanger
- Search Results: bushing
- Search Results: 5 on 5
- Video: Dexter Axle Trailer Axles - Leaf Spring Suspension - 35545E-ST-89 Review
- Video: Dexter Axle Trailer Brakes - Electric Drum Brakes - 23-468-469 Review
- Video: Redline Trailer Brakes 7-75 Review
- Video: Review of Dexter Trailer Leaf Spring Suspension - Bushings - 721590
- Q&A: How To Choose the Correct Replacement 89" Long Trailer Axle
- Video: Review of etrailer Trailer Hubs and Drums - Pre Greased Idler Hub - AKIHUB-550-35-K
- Video: Review of etrailer by AxleTek Trailer Axles - Leaf Spring Suspension - e38GR
- Q&A: Diameter of Trailer Axle Beam with Easy Grease Spindles
- Video: Review of etrailer Trailer Leaf Spring Suspension - 4 Leaf Double Eye Dacromet 5000 lbs Axle - e28SR
- Q&A: Replacement Axle, Springs, Wet Bolts, Equalizers, and Brakes for Tandem Axle Trailer
- Q&A: Should a 3,500 Lb Trailer Axle Have a Slight Bend in It
- Q&A: Replacement Axle and Brakes for 87 Inch Long 3,500 Pound Axle on Travel Trailer
- Q&A: Suspension Hanger Locations for Dual Axle Dump Trailer
- Q&A: Is There a 3,500 lb Axle That is 89 Inches Long With Idler Hubs With 5 on 5" Bolt Pattern