Overall Height of Ultra-Fab Electric Landing Gear # UF17-943010 Including Motor Assembly

Question

Question:

What is the over all length including motor of the # uf17-943010 jack?

asked by: Homer M

0

Expert Reply:

According to my contact at Ultra-Fab, their Deluxe Electric Landing Gear Set # UF17-943010 has an overall height, including the motor assembly, of 36.55-inches with the leg fully retracted. Please refer to the linked diagram, provided by the team at Ultra-Fab, for this and other key dimensions.

expert reply by: Adam R

0

click to enlarge

Answer 1

Landing gear like the #UF17-943010 bolt into brackets that are welded to the frame of the fifth wheel. If the brackets from the existing landing gear can accommodate the 2-1/2 x 2-1/2 housing of the landing gear, and the existing brackets are in…

view full answer...

Answer 2

In order to pick out a direct replacement for the landing gear on your trailer we would need to know the distance between the mounting brackets. Otherwise you could just have the brackets removed from your trailer by a qualified welder and then…

view full answer...

Answer 3

The Atwood 87701-SP three-switch panel that you referred to is now obsolete, no longer made, and none in stock. The only wiring information I could find for you is a poor quality drawing from Atwood/Lippert which I have attached. We do not have this…

view full answer...

Answer 4

The square tube on the Ultra-Fab Deluxe Electric Landing Gear Set, #UF17-943010, measures 2-1/2 inches x 2-1/2 inches and it measures 24-1/4 inches tall. The foot plate measures 8 inches long x 5-3/4 inches wide. I have attached a photo showing these…

view full answer...

Answer 5

The repair kit for your Venture landing gear is the Lead Jack Repair Kit for Stromberg Carlson Landing Gear #LG-146059. It includes the gears and pins required for repairing the lead jack, or the leg that has the motor or crank on it. If you need the…

view full answer...

Answer 6

If the thrust bearing is broken on your VMC900R Venture landing gear you are going to need to replace the leg, which you would need to match by the length of the outer tube, which is likely going to be 29-1/2 inches, but please measure to verify.…

view full answer...

Answer 7

Based on my research your Keystone Raptor Velocity is equipped with Venture Landing Gear. The part number M-900-PK that you found on the lead leg indicates that the correct replacement Follow Leg should be the part #LG-177201. For just the repair kit…

view full answer...

Answer 8

To help I have included the written instructions below and also a diagram that points out the parts mentioned in the written instructions for the entire kit for the replacement gear and shaft kit for your Venture landing gear leg. The instructions…

view full answer...

Answer 9

I linked the schematic diagram for Lead Jack Repair Kit #LG-146059 taken from the written instructions. The complete instructions will be sent to you in a separate link. The follow leg repair kit is part #LC146060 in case you need it.

view full answer...

Answer 10

I went out into our warehouse to pull a Lead Jack Repair Kit #LG-146059 to measure the length of the shaft and found it to be 6-1/2 inches.

view full answer...

Answer 11

The installation of the Landing Gear Set part #RVLG-8000 will be fairly straight forward. Basically, you will need to have a metal support structure so you can attach welded tabs part #LC113511 to it, 15-1/2" apart. Once these are installed you…

view full answer...

Answer 12

The thicker washer of the repair kit part #LG-146059 that you referenced is the thrust washer and the thinner one is the shim washer. I attached a diagram that shows how all of the pieces go together.

view full answer...

Overall Height of Ultra-Fab Electric Landing Gear # UF17-943010 Including Motor Assembly

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching