What is the Front Mount Hitch Position When Curt Hitch 31432 is Installed on a 2010 Jeep Wrangler
Question:
I have seen several front mount hitches for the jeep wrangler which has the 2 in. receptacle over the bumper. Does the 2 in. receptacle go under the bumper on the 31432 hitch, and is there any additional holes that need to be drilled? Thanks
asked by: John S
Expert Reply:
I have seen the same thing on several jeeps. So I was looking at the directions, which I have attached below, for Curt front mount hitch, # 31432, to determine its position when installed on the vehicle. By looking at the instructions, it still is not too clear, though it appears as though the opening will be more or less flush with the center of the bumper.
I spoke with my contact at Curt, the manufacturer, and they told me that the hitch arms mount above the bumper and the actual opening will be just about even with the center of the bumper. Also, there are no extra holes to drill but you will have to remove the air deflector (though the instructions say that trimming it to fit around the hitch is an option).
You might also be interested in a Front Mount Trailer Hitch Receiver Skid Shield, # 6771, to protect the front mount hitch from low-lying obstacles. And if you need a locking hitch pin to deter theft of any accessories, we have the Trailer Hitch Receiver Lock, # e98880. I have included a video review of this lock below.
![Michael H](https://images.etrailer.com/static/images/catg/people/324_tn.jpg)
Products Referenced in This Question
Front Mount Trailer Hitch Receiver Skid Shield - 2" Hitch
- Accessories and Parts
- Front Receiver Hitch
- Skid Shield
- Draw-Tite
more information >
etrailer Trailer Hitch Receiver Lock for 2" Hitches - Flush - 2-5/8" Span - Chrome
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Alike
- Chrome
- Fits 2 Inch Hitch
- Flush Pin
- 2-5/8 Inch Span
- etrailer
more information >
Product Page this Question was Asked From
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Front Receiver Hitch
- Custom Fit Hitch
- Front Mount Hitch
- 350 lbs Vert Load
- 9000 lbs Line Pull
- 2 Inch Hitch
- Square Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Install and Removal of Both the Draw-Tite and Curt Front Hitch on a 2016 Jeep Wrangler Unlimited
- Q&A: Recommended Front Mounted Hitch for a 2023 Chevy Silverado 3500
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Front Hitch Weight Capacity for a 2019 Jeep Wrangler
- Q&A: Recommended Front Mount Trailer Hitch For 2015 Jeep Wrangler Unlimited For Meyer Plow
- Q&A: Difference Between Pace Switchblade, UltraGroove, and JackRabbit Tonneaus for 2020 Ford F-150 5.5'
- Q&A: Front Hitch Receiver for a 2012 Jeep Wrangler Rubicon
- Q&A: Front Mount Trailer Hitch Receiver to Fit 2017 Jeep Wrangler
- Article: Flat Towing Package for 2007-2018 JK Jeep Wrangler and Wrangler Unlimited
- Article: Stability Control for Heavy Duty Vehicles
- Article: Using a Portable Generator on RV
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Best Vehicles to Flat Tow Behind an RV
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)