Hitch and Bike Rack Recommendation for an Older Travel Trailer
Question:
Im looking at item #13432 to bolt directly to the rear bumper of a 46 yr old travel trailer to hold a small bike rack and one bike. Is it possible to find out what the dimensions are for the width between the two upright sides w/holes and the height of each side w/holes? The rear bumper is 1 3/4inch by 1 3/4. Im hoping I can just bring this hitch up underneath the bumper, drill some holes in the bumper itself and bolt it on. thanks for the help
asked by: Steve N
Expert Reply:
The distance between the two mounting brackets of the Curt Hitch part # 9883544 is 3-1/8 inches. It looks like it would be to big for what you are trying to do.
Since none of our hitches that install on bumpers are going to fit your bumper well I believe your best choice would be a multi-fit hitch like the part # 13703. This hitch will fit trailer frames that are between 22 and 72 inches in width so it should fit yours.
You are going to need a bike rack that is confirmed to work at the back of RVs and trailers. Most bike racks aren't designed to handle the harsher ride quality that is present at the rear of an RV/trailer so for a rack that will handle that you would want the # S94FR.
Products Referenced in This Question
Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide
- RV and Camper Hitch
- Frame Mount Hitch
- 22 - 72 Inch Wide Frame
- 350 lbs TW
- 3500 lbs GTW
- 2 Inch Hitch
- Bolt-On
- Weld-On
- CURT
more information >
Swagman E-Spec Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
- Hitch Bike Racks
- Platform Rack
- Folding Rack
- Frame Mount
- Bike and Hitch Lock
- 2 Bikes
- Class 3
- Fits 2 Inch Hitch
- Electric Bikes
- Heavy Bikes
- Swagman
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 4000 lbs WD GTW
- 2 Inch Hitch
- 400 lbs WD TW
- No Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Measure for Trailer Hitch Drop
- Article: Flat Towing Package for 2020 Jeep Wrangler
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Kuat Pivot 2 Swing Away Hitch Extender # PVD20B Weight Capacity
- Q&A: Does Curt Hitch 13432 Fit 2017 Jeep Wrangler Smoky Mountain Edition
- Q&A: Can The Removable Bumper Panel Be Used After Draw-Tite Receiver Is Installed on 23 Grand Cherokee?
- Q&A: Will the Kuat NV 2.0 Fit in the 2 Inch Hitch of a 2021 Toyota Highlander
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Replacement Oil and Grease Seals For PHLE AP3137N2 Oil Seal
- Q&A: Replacement Motor and Actuator for Lippert Through-Frame Slide Out with Tucson 18:1 Motor
- Article: The Definitive, Step-by-Step Flat Towing Setup Guide
- Article: How to Choose the Right Trailer Hitch Class
- Article: Base Plate Adapter Table