Looking for Way to Mount Optronics Backup Light # BUL10CB on Ranger Trail Boat Trailer
Question:
Thanks for the great information. I have to figure out how to wire the lights to my trailer to synchronize with my Yukon and then I'll buy. Your information says it requires a three wire connector. I know one of the wires is a ground. What are the other two for?
asked by: Marvin S
Expert Reply:
In order to mount the Optronics Backup Light, # BUL10CB, on your Ranger Trail Boat Trailer, I recommend using the Rubber Grommet, # a70gb, and Trailer Light Mounting Bracket, # BK70BB.
A wiring harness, part # A49PB for a right angle plug and part # A45CB for a straight plug, will also be needed for the Optronics Backup Light, # BUL10CB.
I have included a few short videos for you to check out.
Products Referenced in This Question
2-Wire Pigtail for Optronics Backup and Utility Trailer Lights - 2-Prong PL-3 Plug
- Accessories and Parts
- Trailer Lights
- Wiring
- Plugs and Pigtails
- 10 Inch Long
- Two Wire
- Straight Pigtail
- Optronics
more information >
Right Angle 2-Wire Pigtail for Optronics Backup and Utility Trailer Lights - 2-Prong PL-3 Plug
- Accessories and Parts
- Trailer Lights
- Wiring
- Plugs and Pigtails
- 10 Inch Long
- Two Wire
- Right Angle Pigtail
- Optronics
more information >
PVC Grommet for 6-1/2" Oval Trailer Tail Lights
- Accessories and Parts
- Trailer Lights
- Mounting Hardware
- Grommet
- 6-1/2 Inch Long
- Oval
- Optronics
more information >
Trailer Light Mounting Bracket for 6-1/2" Oval Trailer Lights, Steel - Black Powder Coat
- Accessories and Parts
- Trailer Lights
- Mounting Hardware
- 6-1/2 Inch Diameter
- Brackets
- Black
- Optronics
more information >
Product Page this Question was Asked From
LED Backup Light for Truck or Trailer - Submersible - 10 Diodes - Oval - Clear Lens - Qty 1
- Trailer Lights
- Tail Lights
- Backup
- Oval
- Recessed Mount
- Submersible Lights
- LED Light
- 6-7/16L x 2-1/4W Inch
- White
- Optronics
more information >
Continue Researching
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Q&A: Replacement LED Top Command Clearance Light With SAE-AP2-16 On Lens For 2018 Sunseeker Motorhome
- Q&A: Replacement for Atwood 70254 RV Landing Gear Switch
- Q&A: Replacement Leaf Spring for Trailer with Dexter 4,400 lb Axle
- Q&A: Replacement Oil Cap for Dexter Hub # 21-35
- Q&A: Window Cover Recommendation for Class C Motorhome Built on F-550
- Q&A: Towing a Trailer with Electric Brakes with a Semi Tractor with Air Brakes
- Article: Trailer Maintenance Schedule
- Article: How to Charge RV Batteries
- Article: RV Cell Boosters, How Do They Work?
- Article: Trailer Wiring Diagrams
- Article: Testing Trailer Brake Magnets for Proper Function
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Trailer Lighting Requirements
Marvin
1/6/2015
Thanks for the great information. I have to figure out how to wire the lights to my trailer to synchronize with my Yukon and then I'll buy. Your information says it requires a three wire connector. I know one of the wires is a ground. What are the other two for?