Summer Starts Here - Save up to 70%
Part Numbers: TLD2124,TLR3507
Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there.
Features:
If you're looking for the best tie-downs for your camper, frame-mounted is the way to go. The frame is the most solid part of your entire vehicle, so it just makes sense to attach your camper to something that's not going to warp, bend, or twist. Even more importantly, the camper's center of gravity will sit lower and its weight will be spread across the entire bed. This avoids a top-heavy load perched on top of your bed rails that's liable to sway and get pushed around by crosswinds. The camper's not going to shift or slide around while you drive; it's going to stay put, and your truck is going to handle just like it does without a camper.
Quick Tip: If you have a plastic or spray-in bed liner, it's important that you use a rubber mat under the camper to eliminate any sliding or bouncing.
Frame-mounted tie-downs are also a great pick for preserving your truck's good looks. The brackets install on the frame, tucked nearly flush with the underside of the vehicle. Remove the arms from the brackets when you're not hauling your camper, and the brackets will be barely visible.
Completely custom to your vehicle, the tie-downs attach to exisiting holes in your frame so that there's little to no drilling and no need for any modifications. Because they're custom, you'll want to use our in-house application guide to make sure you get the exact right model. The tie-downs you need might be different depending on what type of hitch or other accessories you have.
Once the tie-downs are installed, use a set of turnbuckles (sold separately) to secure the camper to the tie-downs. The shank on each arm has 2 pin holes so you can choose how far out they extend, that way the turnbuckles can reach the anchors on your camper without making contact with your truck. Tighten the turnbuckles to the correct level of tension (not too tight!).
Make sure the anchor points are offset from the tie-downs instead of lined up with them so that they will hold your camper from multiple angles. This is important for keeping your camper from shifting. Two holes in the attachment plate of the tie-downs let you find the best angle for you camper anchors.
Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there.
Features:
If you're looking for the best tie-downs for your camper, frame-mounted is the way to go. The frame is the most solid part of your entire vehicle, so it just makes sense to attach your camper to something that's not going to warp, bend, or twist. Even more importantly, the camper's center of gravity will sit lower and its weight will be spread across the entire bed. This avoids a top-heavy load perched on top of your bed rails that's liable to sway and get pushed around by crosswinds. The camper's not going to shift or slide around while you drive; it's going to stay put, and your truck is going to handle just like it does without a camper.
Quick Tip: If you have a plastic or spray-in bed liner, it's important that you use a rubber mat under the camper to eliminate any sliding or bouncing.
Frame-mounted tie-downs are also a great pick for preserving your truck's good looks. The brackets install on the frame, tucked nearly flush with the underside of the vehicle. Remove the arms from the brackets when you're not hauling your camper, and the brackets will be barely visible.
Completely custom to your vehicle, the tie-downs attach to exisiting holes in your frame so that there's little to no drilling and no need for any modifications. Because they're custom, you'll want to use our in-house application guide to make sure you get the exact right model. The tie-downs you need might be different depending on what type of hitch or other accessories you have.
Once the tie-downs are installed, use a set of turnbuckles (sold separately) to secure the camper to the tie-downs. The shank on each arm has 2 pin holes so you can choose how far out they extend, that way the turnbuckles can reach the anchors on your camper without making contact with your truck. Tighten the turnbuckles to the correct level of tension (not too tight!).
Make sure the anchor points are offset from the tie-downs instead of lined up with them so that they will hold your camper from multiple angles. This is important for keeping your camper from shifting. Two holes in the attachment plate of the tie-downs let you find the best angle for you camper anchors.
Average Customer Rating: 4.7 out of 5 stars (3179 Customer Reviews)
Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there. Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there.I was completely impressed with the fitment and overall quality of these Tie-Downs. I ordered them on-line they came quickly and I had them on the truck within a couple of hours with no problems at all, amazing! These things are very sturdy and well-built.
3500 Mega Cab (short bed) 6.7 Turbo Ram & 2018 855s Lance. Needed to build a frame so side to side movement was minimized. The camper will sill walk back an inch or two but have a solution for that also. Torklift equipment is top notch and built to last. Works great!
Tough install drivers side but got it d one
Installation took roughly 1.5hrs, with drivers' side being more of a challenge. Couldn't have taken the 2 factory bed bolts out without an pneumatic impact wrench (and 18mm socket) and a needle nosed vice-grip was key in holding the front welded nut bar while treading the bolt into it. Also, note the driver' and passenger's are slightly different in angles (the instructions could be better to identify which is which, or at least each one marked as such). Looks good and solid! Very happy with the product design and the overall instructions. The corresponding D3109 (rear tie-downs) were very simple installation (~1hr), however the pneumatic impact was definitely needed to take out the 6 factory bolts.
They still work great after a year : )
I added a Super Hitch to my truck so I had to replace the rear tie downs. Two bolts on each unit and easy to reach. Very well made and heavier than the torklift that were attached to the Ram hitch.
They work great
Forklift tie downs are manufactured to exact fit to existing manufactured frame rail holes. They lined up perfectly and after 6000 miles with camper on board have stayed secure. The only downside, (this is relative to when and ware you use you camper) they will corrode when driving through snow covered roads that have been treated with sand and/or salt. I use an oil based product to protect them corroding.
The TorkLift frame mounted tiedowns for my truck bed camper mounted perfectly on my 2016 RAM 3500. They are holding my camper on very securely and will be tucked away nicely when I remove the camper for Winter. I plan on making a footstep to slide into the receivers then, so I have much easier access to my high truck bed when I use it to haul firewood. The only suggestion I have is that we cleaned up the punched out pin hole edges with a file, inside the receivers. The sharp ridges would have scratched the hold down assemblies a bit when inserted into the receivers. Maybe an opportunity for a manufacturing process improvement there?
Easy to install works great
The tie downs were easy to install. I do recommend the use of an impact wrench as that made the installation process straight forward and something a novice can complete in a little over an hour for front and back tie down brackets.
This is the second set of Torklift camper tiedowns I have purchased from eTrailer. As always, the product is outstanding and no other camper tiedown system compares. The service and delivery time was great. eTrailer staff are very good to work with, know their products well, and are quick to respond to questions. If you are looking for camper tiedowns, spend the extra money and get Torklift brand.
Parts were good quality and fit well. Instructions weren't very good, pictures were really poor quality, instructions showed bolts to remove that didn't need to be removed, not always easy to follow.
Great tie downs! They were easy to install, and I love that it is not obvious that the truck has truck camper tie downs when the truck camper is not loaded.
I received outstanding service from Lori at etrailer.com. When I called with questions concerning which truck camper tie down to order, Lori steered me to the correct location on the etrailer webpage and then personally took my order for me over the phone. The speed and efficiency of the etrailer shipping is as good as it gets. I had my truck camper tie down kits within two days of placing the order and I live in Wyoming. I highly recommend this company to anyone wishing to purchase camper accessories online.
My second set of torklift tiedowns ( ford and now a dodge) from etrailer.
The transaction and delivery was fast and efficient and customer service was
better than excellent!
Thanks
Piece of cake install! Very happy with these!
Tiedowns are excellent quality, I read the instructions a couple of times and watched Etrailers video and didn’t have any trouble with installation, pleased with product
Great product, but even better service from etrailer. Had a small issue finding the order, but etrailer customer service quickly helped me locate it. Great follow thru!
Well built and precise. Pretty easy install, just esure you have a good metric socket set and a breaker bar. Air tools help for the rear install!!!!
Thank you for providing Grade 8 Hardaware!!!!!!!!! Nothing gives you a piece of mind like good mounting hardware.
Great product & very straight forward to install with common tools.
Glad I bought these from Etrailer.com - great customer service !
30 min per to install. Clear instructions, all the hardware, no drill application, what more can you ask for!
Very easy to install. Great instructions and pictures for the drivers side installation. Passenger side could use a picture or two, but easyafter iinstalling driver side.
on 2016 Ram 1 ton 4x4 Quad Cab Dually(6.4L gas'r w/8ft bed) drivers side upper bolts were very hard to get started due to Gas tank. Good directions!
I love shopping for all my trailer parts at Etrailer. Between the great phone support and instructional videos, my install goes fast and easy!!!! Etrailer ROCKS!
Ask the Experts about this Camper Tie-Downs
Do you have a question about this Camper Tie-Downs?
TorkLift Accessories
Fit to this rack on your 2017 Ram 3500
Info for these parts were:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.