Part Numbers: SB324-168,C31433
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Remove snow quickly from your driveway or parking lot with this hitch-mounted snowplow. Pivoting, 3-position blade glides over uneven ground. Long-lasting actuator with internal clutch lets you operate plow from your warm cab.
Features:
Specs:
Note: Due to the size of this item it ships via truck freight.
The SnowBear Proshovel conveniently slides into your vehicle's front-mounted trailer hitch for easy, convenient mounting. Smoothly and easily raise and lower the plow from the comfort of your cab with the remote-controlled electric actuator. The pivoting blade makes this plow ideal for rocky or uneven surfaces because it can adjust to the terrain. Angled trip springs are also built in to help keep the blade from catching and tripping.
Simple, Hitch-Mounted Installation
This hitch-mounted snowplow simply slides into your vehicle's front trailer hitch receiver, making it a breeze to install. Unlike a plow that attaches to custom-fit brackets, which ties you down to just 1 vehicle, this hitch-mounted plow can be used on most trucks or SUVs with a 2" x 2" front-mounted hitch. As a result, this plow can be easily switched between multiple vehicles. And because it offers a nearly universal fit, you won't have to buy a new plow when you replace your old vehicle.
To install the Proshovel snowplow, just slide the shank of the plow assembly into your 2" trailer hitch receiver . Then use a pin and clip or a hitch lock (sold separately) to secure the plow in the receiver.
How to Plow
Once the plow is mounted on your vehicle, lower the blade and set it to the desired angle. To set the angle, exit the vehicle and manually position the plow straight ahead, or 22 degrees to the left or to the right. Angling the blade allows you to push snow off to the side where you want it without having to change the angle of your entire vehicle. This is especially useful on a driveway or private roadway where piling the snow straight ahead would create a barrier.
To begin plowing, just drive forward. When backing up to take another pass, be sure to lift the plow with the remote or the in-cab toggle switch, then lower it again before moving forward. When approaching a large pile of snow, be sure to decrease your speed. Slamming into a pile of snow can void the warranty on the Proshovel.
When you are finished, put your vehicle in park and lower the plow. Remove the plow from your vehicle after every use.
Smooth, Controlled Lifting with Electric Actuator
The electric actuator on this plow allows you to lift and lower the blade using a toggle switch that mounts in your cab. You can also use the included wireless remote control. To raise the plow, activate the actuator. As the actuator moves along the internal screw, the arm on top of the actuator will pivot, raising the plow blade by pulling the chain that is attached to it. Having fewer moving parts than a typical winch makes this setup less complicated and less likely to break down than other plow lifting and lowering devices. There is also an internal clutch system that prevents damage to the actuator should you try to raise the blade too high or lower it too low.
Easily attach a variety of accessories to the front of your vehicle with this fully welded, corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.
Features:
Specs:
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
Average Customer Rating: 4.6 out of 5 stars (20 Customer Reviews)
Remove snow quickly from your driveway or parking lot with this hitch-mounted snowplow. Pivoting, 3-position blade glides over uneven ground. Long-lasting actuator with internal clutch lets you operate plow from your warm cab. Easily attach a variety of accessories to the front of your vehicle with this fully welded, corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.I purchased a SnowBear Proshovel Snowplow and a 2" Draw-Tite Front Mount Trailer Hitch Receiver for my 2001 Ford Explorer Sport Trac. The front mount hitch receiver was a breeze to mount to my vehicle. Literally 15 minutes from start to finish. When the SnowBear plow arrived I was a little apprehensive, as it came in 3 separate boxes and some assembly was required. The directions included were phenomenal, easy to understand and took you through complete assembly step by step. This has been a wonderful experience and I could not be happier.
Fit was tight but with a floor jack I was able to install. Looks like it will work well for me. The bolt guide wires were critical to installation. Very good construction of the hitch.
After correcting a mistake and taking another receiver back at their expense, etrailer shipped me the correct hitch for my 2017 Jeep Wrangler Rubicon Recon. If your Wrangler has the steel Hard Rock / Anniversary Edition bumper in the attached pictures, this is the right receiver. It's very well made and has a much better paint job than the Draw Tite that didn't fit my Jeep. The tolerances are VERY tight, so much so that I had to hammer it into place with a block of wood. The supplied fishwires made getting the carriage bolts and spacers in place a breeze. Unfortunately, you will have to remove the steel skid plate that's attached to the bumper. I thought it might be possible to cut it around the hitch and put it back, but it doesn't look there's enough clearance. Great service from etrailer!
First one purchased came with correct item Nr on the box but inside was a 1” hitch for small sedan. Second came correct but was an 1/8 too small. Welds weren’t square and warped. Make sure to verify your vehicles measurements. I wound up grinding and having to repaint the hitch. Only needs to support a front rod holder or I would have returned it again. Sometimes ya fight your own battles
Directions were clear and concise, however the side brackets were slightly narrower than the vehicle frame and it needed a fair amount of convincing to slide up and over into place. Furthermore the driver side superior bracket hole was offset just enough not to allow the bolt to pass through the frame. The hole in the frame had to be slightly enlarged. Otherwise it looks great!!
this is the only hictch i have found that is not custom made that will work with my aev bumper that is on my jk. fits perfect and i can still put a winch in my bumper. you will need a hammer to get it in place though it tight. it does hang down a bit low so you will loose some ground cleance, the aev and the skid plate had to be removed but it will be fine. i needed a way to carry cooler and fishing rods this will work great.
Great fit went on in 30 minutes. can confirm it will fit with the Warn winch bumper.
By moving the secondary mounting bolts from the factory bumper to the front frame crossbar this front mount version for Jeep JK allows for the installation of many aftermarket bumpers, which will be my next project. These Curt mounts are super solid. I have had one on my '98 Cherokee for the last 6 years for plowing snow. The mount is fine but the Cherokee is tired. ;-)
My install took 30 mins.
your service and speed of delivery were great. now i have to put it on and see how it fits. on the down side the hitch was not packed very well and the paint was cracked off in several places. i will have to use touch-up paint so it doesn't rust. its going to be under the jeep so i won't really see it, its not worth the hassle sending it back because i want to use it this weekend. your phone staff was very nice.
By the way, are tongue weight and vertical weight different measurements??
Great fit Well made
Bolted right on but a little tight. A big hammer did the trick. Once again a nice hitch. Now I have on front and back of my jeep JK.
The part bolted right in, took about 20 minutes to complete. My second product bought, and a great company to work with.
Looks great. Well made. Installed in under 30 min.
Strong work,
Overall it's a good light duty plow, works like it's supposed to, clears the snow with no problems. Originally purchased the plow with the hitch receiver mount, But the plow stuck out quite a bit in my opinion plus there was to much wobble. So I converted to the 2 point mount which brought the plow in closer and a lot less wobble.
There was an issue with the actuator, it would work intermittently when lowering the plow but Snow Bear covered it under warranty and sent me a new one.
My only gripe is that only after 3 months of Winter use, the whole plow was showing a lot of surface rust and the paint was peeling.
Overall it is a good setup, does the job it's suppose to. Had one problem with the actuator intermittently working when lowering the plow, but was replaced under warranty.
Originally purchased to use in a front mounted hitch receiver, but switched to the two point hookup which brought the plow in closer to the vehicle and made it a little more stable.
My only problem was after 3 months of winter use, paint was peeling and a lot of surface rust showing.
Bolted up with little effort. Work's g reat!
Ask the Experts about this Snow Plow
Do you have a question about this Snow Plow?
Info for these parts were:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jeep Wrangler Unlimited Accessories
Mike L.
1/22/2019
Essentially, theyre the same thing. Tongue weight and vertical load limit represent the maximum amount of downward force that can be applied to the receiver tube.