I called my friend over at Thule and they said they do not have the replacement knob available separately. The Replacement Knob for the Thule Apex # TH79JV is a different part number with only the Thule Apex and the Thule Raceway as confirmed fit. Since the Thule Helium Aero 3 was phased out, support for replacement parts is limited.
If you are able to find the correct replacement knob someway somehow, then the Replacement Lock Cylinder and Premium Key # 1500004217 is the correct replacement... view full answer...
Yes, you can use the Dexter Electric Trailer Brake Assembly with Parking Brake # 23-112 to replace your current Electric Trailer Brake Assembly # AKEBRK-7L-D as long as your axle is a 6,000-lb axle.
The Dexter Electric Trailer Brake Assembly # 23-112 also has a manual parking brake lever included.
If you need new mounting hardware, you can use the Mounting Bolts and Hardware for 12" Brake Assemblies # BRKH12. view full answer...
The Classic Accessories Toy Hauler Screen for Fiberglass or Aluminum Toy Hauler # 052963799842 that you reference will install to your toy hauler via the included rip-and-grip strips. These are similar to Velcro in that you peel back one side of the strip which will then stick to the trailer. The rip-and-grip on the screen will then attach to the rip-and-grip portion that you just installed on the trailer.
The screen for a Steel Toy Hauler # 052963799941 will install the same way.
I contacted... view full answer...
I recommend using a cargo carrier that will have enough clearance as you mentioned you need. One of the nice carriers we offer is the Curt 24 x 60 Cargo Carrier, part # C18151.
This carrier has a distance of 9 inches from the center of the hitch pin hole to the closest edge of the carrier when folded up and 19 inches when folded down. This carrier has a shank rise of 2 inches and measures 61-3/4 inches wide x 25-1/4 inches deep x 6-1/2 inches tall outside dimensions. view full answer...
The only way to carry a kayak and/or canoe on the 2020 Ram 1500 while towing is to install a roof rack on the truck and use a carrier. I recommend the Yakima JetStream Crossbars part # Y00427 because they are aerodynamic and their built-in ridges help control air flow to cut down on wind noise. They also have a nice T-slot channel that allows you to mount accessories with a rubber strip that does not need to be trimmed to add accessories like other brands. You will also need the BaseLine... view full answer...
Westin Fey Universal Rear Bumper # 66000 is a general-purpose part intended for use on many different older vans and pickups starting with late-70s model years. It does not offer a custom-fit on any one vehicle so some modifications to a compatible vehicle and/or the bumper itself are required. It may be usable on a Frontier but we offer no install kit for your vehicle.
We do not have a custom-fit replacement bumper for your Frontier but we do have other custom accessories like tube steps,... view full answer...
We have two options for you to use an adapter with your 12V accessory with a 110V outlet.
They are the AC to DC Adapter for Swift Hitch Wireless Camera System, part # PP01, and the Power Converter for Fan-Tastic Vent Endless Breeze Portable Box Fan, part # FV1101-09.
The PP01 is obviously more compact and easier to carry around (and not trip over). The FV1101-09 allows for more amperage to come through for accessories that need higher settings. view full answer...
Installation of the # LC305339 will only require plugging the leg wiring harness into the wiring harness attached to your controller. I have attached a wiring diagram for the 4-point and 6-point system below. view full answer...
The T-Slots on the Yakima LockNLoad Platform Rack # Y05044-39 have the same dimensions as standard crossbars so you can basically use any brand of T-Bolts to accomplish your job. For example, you can use the Thule Square T-Bolt # 853208914 or the Malone T-Slot Fit Kit # MPG8287. view full answer...
I spoke to my contact at Valterra and she said the reason the D&W Inc. Spray-Port RV Exterior Hose Hookup - 2-3/4" Round - Black # PF147006 says it is for non-potable water is to stay in accordance with the Safe Drinking Water Act. The water from this hookup is not recommended to be used as drinking water.
Any of the hose hookups that we carry will be for non-drinking water. view full answer...
It sounds as if you're speaking of the T-bolts. We offer the Yakima replacements as part # Y8880184, which includes 4 nuts, bolts and washers. Thule doesn't offer a nut compatible with the # 853-208909 bolt, as it's meant to be used with a knob. view full answer...
In order to wire the Derale 26" Dual High-Output, Electric Radiator Fan-and-Shroud Assembly part # D16927 to a manual switch you will need two of the Derale Lighted On/Off Switch for Electric Fans part # D16740. There are three terminals on the switch which are for accessory, power, and ground. The accessory terminal will need to be attached to the yellow wire on the included relay harness. The power terminal will need to be attached directly to the positive battery post and the ground... view full answer...
The Replacement Threaded Pin for Thule Snug Tite Hitch Lock and Anti-Rattle Device # 853-5917 is 12mm by 1.75 inches. This is just the threaded bolt, you'll need to use the flat washer, lock washer, and lock assembly to secure it. If you need the whole Thule Snug Tite Hitch Lock Kit # THSTL2 includes everything.
I have attach a review video link below. view full answer...
I really like the etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2" part # e98912 . This hitch offers really easy installation and is mainly hidden with just the receiver tube opening being exposed (see photo). This one has a lot of bang for the buck when comparing it to others because it can be used for towing or for recreational use(bike racks, cargo carriers, etc.)
The Stealth Hitches Trailer Hitch Receiver w/ Towing Package - Custom Fit - 2" part... view full answer...
If you will not be using the base plate kit then we recommend using plugs to protect the inside from rust, the Roadmaster Base Plate 1-1/4" Receiver Covers part # RM-212 are a confirmed fit for the Roadmaster Direct Connect Base Plate Kits.
Unfortunately, there are no other accessories that will attach to these such as a brush guard. view full answer...
You are correct about part TH04851. It is no longer available. Both the bolts that came with that discontinued part kit and bolt # 915-068-054 are M6 bolts so you will be able to use the longer # 915-068-054. This bolt is sold in quantities of 1 so you would need 8 of them total to replace all the bolts in the original kit. view full answer...
Yes the Dexter brake assembly part # 23-459 is the correct right hand side brake assembly for the trailer axle you have. The matching other side would be the # 23-458. view full answer...
The Classic Accessories Toy Hauler Screen for Fiberglass or Aluminum Toy Hauler # 052963799842 has an adjustable width and height design for a perfect fit. It is not designed to be rolled up and doesn't have built in straps to hold in that way although rolling the screen won't hurt the screen. The design is to remove the screen when you don't need it. It has rip-and-grip strips it utilizes for easy installation and removal.
When in use, it has dual zip-open screen panels and has detachable... view full answer...
Go To Results