The overall height of the MORryde StepAbove part # MR85RR above where it mounts to the door frame is 47-3/4 inches which would be the same amount of distance you'd need between the side of your RV and anything to the side of it to allow the steps to swing down. view full answer...
You should measure the height of the step that is currently on your RV to determine if the Econo Porch Trailer Step with Handrail # EHS-102-R would work well as a supplemental step system for your RV.
The # EHS-102-R has a height of 21 inches, so if your RV steps are about 21 inches or slightly higher then this would work well to transition from the RV step to the ground.
This product weighs 56 lbs, I would not recommend attaching it to the rear ladder of your RV and would recommend you... view full answer...
The MORryde StepAbove RV Steps # MR85RR weighs about 70 lbs. As far as the flip step, I assume you are referring to the MORryde Flip Tread RV Steps # MR42UR which weighs about 45 lbs. Both of these steps will fit your 28" wide door. Personally I like the MORryde StepAbove RV Steps just because of how stable they are. There is no movement or bouncing when you use the steps like a lot of other RV steps. They are a bit heavier than others but they are really not difficult to open and close,... view full answer...
Yes, you can change the steps on your RV from electric to manual. You would just need to take some measurements after deciding what style you prefer.
You can look at steps like the SolidStep Manual Fold-Down Steps # LC791574. This style of step would require to take measurements of the doorway width and entry height. This style folds up into your RV behind the door.
You can also look at steps like the Lippert Manual Pull-Out Step for RVs # LC432682. This style of step would mount underneath... view full answer...
Yes we have the step rugs for your MORryde StepAbove RV Steps # MR98RR. The Prest-O-Fit 3-Piece Step Rug Set is available in Black # PR53SR or Brown # PR33SR for your 2nd gen steps with the 19-1/2" treads. These rugs will also fit the following steps.
MORryde StepAbove RV Steps # MR48RR
MORryde StepAbove RV Steps with Strut Assist # MR45RR view full answer...
Yes, the Prest-O-Fit 4-Piece Step Rug Set for 2nd Gen MORryde StepAbove RV Steps - 19-1/2" Wide - Black # PR63SR is a compatible fit for your Second Gen MORryde RV Steps # MR88RR. view full answer...
I could not locate anything specifically from the STP-015-MR226-09 number. It looks like that may be an OEM part number for whoever manufactured your RV.
From the little information I could find, it looks like it may be the OEM equivalent of the MORryde StepAbove RV Steps # MR26RR. The correct replacement leg would be the Replacement Leg for MORryde StepAbove RV Steps # MR36DR.
The Replacement Leg for MORryde StepAbove RV Steps # MR36DR works with all 2nd generation MORryde StepAbove... view full answer...
The Econo Porch Trailer Step part # EHS-102-R would work well for you as long as the overall height of the steps match what you would need. The third step will be 21 inches off of the ground so you would need to compare that to the steps of your future RV to know how the steps would match up.
It would be also a matter of placing the steps in the correct location relative to the power steps that come out on the RV. view full answer...
You will need specific steps from Lippert in order to use the Replacement Step Control Module for Lippert Components Tread Lite Powered RV Steps # LC334850.
This is a replacement part that is specific to Lippert Electric Tread Lite Steps so you will need to have one of the following step parts in order to use this, as we would not be able to verify its compatibility on any other steps. It will work with the following:
- Lippert Electric Tread Lite Step for RVs - Single - 24" Wide # LC353542
-... view full answer...
When measuring for a standard aluminum (or any material) set of RV steps you want to measure from center of bolt hole on one bracket to bolt hole on the other bracket of your existing steps. You can also measure the width of the doorway of the RV (where the steps install) if you are not able to measure the existing steps.
We do offer RV steps with 4 steps but you would have to make sure you have the ground clearance for an extra step. You want to measure from the bottom of the doorway... view full answer...
Unfortunately Thayne, I have no way to look up what parts were installed on your 2008 Coachmen Freedom Express 21QB motorhome. So you are going to need to measure for the width of your step and the amount the step needs to drop. Here is a list of the different single steps we offer with the widths.
Kwikee Electric RV Step Complete Assembly - Single - 26 Series - 23-1/2" Wide # LC3711363
Kwikee Electric RV Step Complete Assembly - Single - 28 Series - 23-5/8" Wide # LC3747453
Kwikee Electric... view full answer...
Most powered RV steps are wired up so that if you turn on the RV the steps will automatically retract. If yours is extending instead that would indicate that this circuit is wired backwards. Do you know what steps you have? view full answer...
I believe you're looking for the Replacement Step Frame for Kwikee RV Electric Steps # LC3747457. This is just the step frame only, and is a direct replacement for the Kwikee Electric RV Step Complete Assembly - Single # LC3747453.
If you have a different step, let me know and I'd be happy to help. Attached are a couple of videos for you to check out as well. view full answer...
We do have just the replacement steps without the motor, control unit, and switch kit. I'm assuming you have Kwikee steps on your 2019 Thor Windsport Motorhome. We have the following available:
-Replacement Step Frame for Kwikee RV Electric Steps - 25 Series - 24" Wide # LC3658374
-Replacement Step Frame for Kwikee RV Electric Steps - 32 Series - 24" Wide # LC3722618
-Replacement Step Frame for Kwikee RV Electric Steps - 28 Series - 23-5/8" Wide # LC3747457
-Replacement Step Frame for... view full answer...
The correct replacement step motor for a set of Kwikee 35 Series Electric RV Steps is the Replacement Motor for Kwikee Electric RV Steps part # LC379147. view full answer...
We have electric retracting/extending RV steps for fifth wheels like with the Kwikee RV Step Assembly part # LC375821. The steps are 30 inches wide and the mounting bracket is designed to bolt on. For a narrower step setup we have the part # LC3694042 which is 24 inches wide. You'd need to measure the step area on your RV to see which size you'd need. We don't have a 4 step setup. view full answer...
To replace your Kwikee Series 32 903206000 RV steps you'll need the Kwikee Electric RV Step Complete Assembly # LC372261. This kit will come with everything you need; steps, motor, switch kit, and controller to completely replace your outdated RV steps. view full answer...
Wider steps can be installed on RVs but what you'll have to do most likely is remove the old brackets that steps used and install new Outriggers like part # LC301704 to give the new steps something they can attach to. view full answer...
The Econo Porch Trailer Steps, # EHS-102-R, are stand-alone steps that you would place in front of the door of anything. They do not attach to the vehicle so you can use them with your Dutchman RV. They can fold up for storage by removing the braces that normally hold the stairs upright.
For steps that attach to the RV you could use Scissor Steps # SS03. It comes with a bracket that attaches to the RV and the steps attach to that for easy on/off operation. view full answer...
The Alumi-Tread Manual Pull-Out Step for RVs # LC432698 can install in place of the MORryde steps you have now. There's a chance the brackets you have now could fit directly or be modified to fit but worst case scenario we have brackets with part # LC301704 that you can attach to your RV frame to mount the steps. view full answer...
Go To Results