We've got exactly what you need. You can order a replacement hardware kit for a hitch with part # RHK. You'll go to that part's page and put in the part number of the hitch you have for your 2014 Toyota Sienna (or any Curt or Draw-tite hitch that is compatible with your vehicle) in the box on the page and receive all of the mounting hardware required to get your hitch installed.
For reference, the Curt # C13343 is a confirmed fit on your 2014 Sienna and can be used in the field marked... view full answer...
We do have just the hardware available for the Draw-Tite Max-Frame Trailer Hitch Receiver # 75237. The correct hardware is going to be the Replacement Hardware Kit for Trailer Hitches # RHK. You will then need to input 75237 in the Hitch Item Number Box and select Draw-Tite from the Manufacturer drop down. I have included a picture of what this looks like. view full answer...
The Dexter DX7.5 Drop-N-Go Brake Actuator # 099-175-20 is a direct replacement for your Tie Down model 70E disc brake actuator with a 7000 lb capacity (Tie Down was bought out by Dexter back in 2017).
Although I don't have a way of decoding your VIN, you should be able to call Load Rite and provide them with your VIN - they will be able to tell you exactly what kind of axle is on your trailer. If you can get back to me with your exact axle capacity and wheel bolt pattern, I will be happy... view full answer...
You would need to convert the 4-way to a 7-way so that you can install the brake controller. For that you will want the Brake Controller Install Kit and 7-Way Adapter part # ETBC7. I attached installation instructions and an install video for this product as well.
For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup. view full answer...
It looks like you have found it already, the Replacement Hitch Hardware Kit part # RHK. In order to get the correct components you'll simply need to input "C13105" into the item number box. view full answer...
We sure do! The etrailer Replacement Tow Bar Adapter # e98974 is the piece that you're looking for on your etrailer SD Non-Binding Tow Bar # e44ZR.
As long as your tow bar was sitting away from this piece when it was damaged then you're good to go - otherwise I would double check the operation of the tow bar just to make sure it's in good shape. view full answer...
The # 37185 is the exact 7- & 4-way plug that is included in the # ETBC7 kit. We kit the # 37185 together with the # 5506 kit and some zip ties and wire loom to make a complete kit.
The # 37185 will include the cover for the 4-way connector. To replace the 7-&4-way connector you will also need to re-splice your connections to the new wiring, this also comes with the 4-way connector for your already existing wiring harness.
For a 4-way dust cover for your trailer end connector, you will... view full answer...
Yes, you'll just need to know item for the hitch and enter it in on Hitch Item Number box above the add to cart button on the Replacement Hardware Kit for Trailer Hitches # RHK page. view full answer...
The Dexter Driver # K71-773-01 and Passenger # K71-773-02 side calipers are replacements for the Titan 225 calipers. These calipers include new Brake Pads # T4870900 view full answer...
CIPA replacement side mirror # KS70029T is a custom fit, vehicle specific part. If your 2000 Toyota Sienna came with factory powered mirrors WITHOUT a heat function then # KS70029T is the correct replacement. If it has power and heat features use # KS70023T (5-pins). Since you need a 5-pin connector mirror # KS70023T would be the way to go. view full answer...
When calculating tongue weight for a weight distribution system you would not add the weight of the system into the calculations. Essentially it becomes part of the vehicle frame and would not be tongue especially considering it actively reduces it. I know this is a weird concept but I have had several conversations with our WD manufacturers and they all state that it would not be considered as tongue weight in regards to the towing setup.
I would recommend the Reese Strait Line part #... view full answer...
With replacing your Curt T-Connector Vehicle Wiring Harness # C56261 you can reuse the same power wire running to the battery. This wire is connected with a Butt Connector # DW05745-1 and can be simply replaced with the new kit. view full answer...
To replace the air line tubing on your Air Lift 1000 Air Helper Springs for Coil Springs # AL60732 you can use part # AL23RV. This comes with 50' of tubing to redo both lines. I highly recommend using a tube cutter # AL10530 to get a straight cut and help prevent any future leaks in your air spring system. view full answer...
We carry a whole range of electric RV steps shown on the linked page. If yours are 28-inches wide then you may very well have the Lippert Kwikee 33-Series steps like # LC372266. The replacement control modules and magnetic switches available are shown on the other links. view full answer...
Sounds like you have the Curt 4 Bike Rack # C18030 on your 2015 Toyota Sienna. First, for the anti-rattle lock, if you want to replace just the bolt, the official Curt part is # C22321 which has a nice bracket for extra sturdiness. If you're looking for a locking option, then the SportRack Anti-Rattle Hitch Lock # SR0901 is a confirmed fit for Curt bike racks.
As for replacing the shank on your Curt 4 Bike Rack # C18030 to make it a pure 2" bike rack, Curt does not offer that part. If... view full answer...
Since the Yakima bike rack part # Y02457 comes with a locking threaded hitch pin bolt there isn't a way to use the J-pin with it and it isn't needed. That being said we have found that adding the Yakima HandCuff Cable Lock for RidgeBack and SwingDaddy Bike Racks # Y02466 adds extra security for your bikes.
This would work great with the Draw Tite hitch part # 75237 that you mentioned as well. view full answer...
Yes, it sounds like you'll need the Replacement Adjustment Knobs # Y8880148 and the Replacement Upper Claw Base # Y8880279 to connect your RailGrab to your 2017 Toyota Sienna.
The Yakima RocketBox Pro 14 # Y07192 is a great roof box for your Sienna. It holds 14 cubic feet of gear, includes Yakimas SKS locks, and is easy to install. I've attached a video of the RocketBox Pro on a 2015 Sienna so you can get an idea how it would fit on your van with the rear hatch and sunroof. view full answer...
We do have a suspension enhancement solution that will work with your 1998 Toyota Sienna. I'd recommend the Firestone Coil Rite Air Helper Springs, part # F4118. The nice thing about an air system is you can tailor the firmness of the suspension to fit what you're carrying or towing. The air pressure can be adjusted from as little as 5 psi all the way up to 35 psi.
Timbren doesn't offer a solution for your vehicle, but in all honesty the Air Bag solution would be a better option because... view full answer...
We do have replacement end caps for the Malone AirFlow2 Roof Rack # MPG216.
What you will need are the Replacement Endcaps for Malone AirFlow2 Roof Rack Crossbars # MPG1012. view full answer...