I believe what you are asking about is the hall effect sensor. Yes, the Replacement 24-1/2" Left Rear Leg - Lippert Ground Control 3.0 Electric Leveling System # LC305339 does have the hall effect sensor in it. Assuming you have the Lippert Ground Control 3.0 automatic leveling system # LC358590 or # LC675817 this is the replacement leg you are looking for. view full answer...
There are a couple possible grease seal sizes for the hubs on your Grand Design 6,000 pound Dexter axles, so the only sure way to determine the right one will be to pull one the hub assemblies and take a look at the existing seal. There should be a number stamped on the seal itself identifying its size, but if it's too worn you can also measure the outer diameter of the spindle where it sits (or the diameter of the seal if it's in good enough condition).
Most likely you will need either... view full answer...
I looked up the specs of the Flojet 030526144 and they are 2.9 gallons per minute and 50 PSI. The HydroMax RV Fresh Water Pump # P25201 is 3 gallons per minute and 55 PSI.
The HydroMax will work as a replacement water pump for your 2015 Grand Design Reflection. It mounts in any direction so installation should not be major reconstruction. view full answer...
No, the etrailer # e28SR would not work for your 2017 Grand Design Reflection with 5,200lb axles.
To find the correct spring you need to jack up one side of the trailer so there is no weight on the spring at all, as weight will make the spring get longer, and then measure from center of eye to center of eye.
If the 26" measurement is with weight on the spring, then there's a good chance you'll instead need the # e76SR instead which has a 5,300lb rating and measures 24-7/8" long.
Let... view full answer...
Yes, we have the tie plates you're looking for that will fit a 3" axle. The # RM22MR is the C003169 with the notch and the # RM54GR is the C003170. Using these will convert the shock kit portion of your comfort ride system into the # RM-2460. view full answer...
Yes, the Mighty Cord RV Power Cord part # A10-5025ED90 would do a great job replacing the Furrion 50 amp 25 foot long cable you have now. This is also a 50 amp cord that is 25 foot long so it would work just as well. view full answer...
We sure do! I believe you're looking for the Replacement Weld-On 5th Wheel Landing Gear Leg Bracket for Lippert RV's # LC113511.
This is a standard weld-on frame bracket that is designed to work on LCI assemblies like your Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin # LC179013, and has measurements of 2" long x 3-1/2" wide x 4-1/2" tall. view full answer...
If you can let me know what the pin box number is on your 5th wheel I can let you know which MORryde upgrade will be correct. There should be a sticker on the side of your pin box with a number listed on it that I'll need.
For example, the part # MR74VR is for 11.5K - 14.5K 5th wheels with 1621 and 1621HD pin boxes while the part # MR77VR is for a 11.5K - 14.5K 5th wheel with a 1116 pin box. These are the 2 most common pin box numbers so they will likely be a fit but if you have something... view full answer...
For your 2016 Grand Design Reflection 29RS, we have two possibilities for replacement springs that work for 4400-lb axles.
You need to measure from the center of one eye of the leaf spring to the center of the other to get the proper length. However, since yours are flat, they have stretched quite a bit. So, an accurate measurement will be difficult. More than likely, you will need the 26"-long 6-Leaf Double-Eye Spring for 4,500-lb Trailer Axles, part # e27SR I've linked to a video review... view full answer...
I was able to find information on another 2021 Grand Design Reflection 303RLS showing it came with a Dexter Axle and the Nev-R-Adjust Electric Trailer Brake Kit # 23-458-459. This requires the Left # K71-675 and Right # K71-676 brake shoes. I recommend verifying you also have Dexter axles and the axle tag states you have the Nev-R-Adjust brake assemblies. view full answer...
The Progressive Dynamics Inteli-Power RV Converter and Smart Battery Charger # PD9270 your looking at is rated for 70 Amps so while you can technically do this I recommend going with the 60 Amp Version # PD9260C instead because it's a direct replacement for your WFCO 9855. We always say to stick with parts closest to your initial rating so you don't accidentally overload something.
You can also pick up the Converter Status Remote Pendant # PD92201 to get a visual on the charge status of... view full answer...
The MORryde Cushioned 5th Wheel Pin Box # MR74VR (11,501-14,000lbs) is the correct replacement for the pin box on your 2021 Grand Design Reflection 303RLS. This pin box has the correct bolt pattern(1621) and weight capacity(11,995lbs GVWR) for your Reflection.
Your Reflection 303RLS has a 1621 Pin Box # LC1191191 from Lippert. view full answer...
It appears you will need the MORryde Suspension Upgrade Kit # MR46ZR for your 2021 Grand Design Reflection 303RLS. These shackles measure 2-1/4" from center of shackle hole to center of shackle hole. We also have the 3-1/8" Kit # MR76ZR if you have the longer length shackles.
I recommend filling the wet bolts with Grease # L11390 using the Grease Gun # L30416. The flexible hose and pistol grip handle make it easier to reach all the bolts. view full answer...
The Replacement Tightening Knob for Solera Awnbrella Bow # LC346848 does not come with the square nuts which I presume you're referencing to the Replacement Hanger Block for Solera Awnbrella Support Bow # LC386206.
If you need any other replacement parts for your Solera Awnbrella Support Kit for 8' Projection RV Awning # LC362237, we also offer:
-The Replacement Label for Solera Awnbrella # LC387444.
-The Replacement Rubber Tip for Solera Awnbrella Support Bow # LC386207.
-The Replacement... view full answer...
The 10" x 2-1/4" Electric Brake Shoe/Lining (One Wheel) # BP04-095 are the brake shoes for the Dexter electric brakes and they will fit the Axletek brand just fine. The # AKBRKR-S-10 are also a fit for your 4,400 lb axles. view full answer...
Yes, the Grease Zerk # LC44XV for your Lippert Tandem Axle Equa-Flex AP Kit # LC64FR can be replaced as it is removable. Do note that this grease zerk is specific to Lippert as it has a special tapered thread that is not commonly used by other manufacturers.
We also have replacement Wet Bolts # LC126238 and # LC126197 if the bolt is damaged or the threads are broken off inside the bolt. view full answer...
Thank you for the image of your axle tag. Your Dexter 5,200lb axle uses a Grease Seal # GS-2250DL. We do have this as a Pair # RG06-070 for both of the hubs on one axle.
We also have the Bearing Kit # BK3-300 that will include the bearings along with races and a grease seal for one of your hubs. I recommend keeping one of these along with Grease # L11390 in your 2021 Grand Design Reflection 303RLS 5th wheel just in case you have a bearing go out on a road trip. view full answer...
For your 2018 Grand Design Reflection 337RLS you need a 6,000 lb axle with an 86-1/2" hub face measurement and 68-1/2" spring center length. Since the spring seats can be moved, you can use the Trailer Axle Beam with Easy Grease Spindles # e33GR as a replacement.
This axle matches your current axle length and has a spring center measurement of 71-1/2". You will need to cut off the spring seats on the # e33GR and weld on # TRSS300 to match your current spring-center-to-spring-center length.... view full answer...
For your 2019 Grand Design you will want to use the MORryde Suspension Upgrade Kit # MR46ZR. The Kit # MR58ZR you found is for 5th wheels using the Correct Track system for aligning the trailer axles. This kit will allow you to replace all your shackles, wet bolts, and bronze bushings included with the Dexter EZ Flex # K71-653-00 in one easy kit. view full answer...